Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Hi,
i tried to send data from ios 7 via tx_characteristics(like in UART example) but received error:
didWriteValueForCharacteristic 2A38 error = Error Domain=CBErrorDomain...
I have been trying for a few days now to get my environment setup for development with the nRF51822. Since there is no official configuration for the Mac w/ Eclipse I have...
Apologies if this has been asked before but did search for 'format' in faq and got nothing.
I have been answering to questions.
In my answer I place hard empty lines....
Hi
i use nrf51822 s110 "hrs" example to transmit the data to ios.
I need to add an option to send back some data (from ios to nrf51822). 10 bytes maximum .
how can i implement...
I am implementing Device Firmware Update using BGLib on C# using BLED112. When i am writing on the DFU Data point on Peripheral (which is a Nordic's nrf51 chipset), i need...
hi,everyone.
version:sdk10.0
i know the nrf51822 system running order is: softdevice->bootloader->app.But i have a question when i am reading bootloader. If the program...
I have a question about the wait_for_flash_ready routine in the nrf_nvmc.c file.
static inline void wait_for_flash_ready(void)
{
while (NRF_NVMC->READY == NVMC_READY_READY_Busy...
Hey,
I have my nrf 52 dk and nrf connect 1.1.1.
I have soft device v3 on my nrf 52.
I connect my board into my computer, NRF connect recognizes my board and gives me...
Hello,
4 of 5 times when i want to connect to my firmware using RTT the firmware crashes.
Commands that i use are:
terminal one: JLinkExe -if SWD -device nrf52 -speed...
Hello ,
I'm using nRF52810 with SDK 14.1 base on ble_app_uart example. where i am continously receiving the GPS data via UART. i am putting my GPS module in sleep mode...
Hello,
My setup is: ble_uart_app example, custom board with nrf51822, sdk 6, s110, nrf connect for pc.
I am advertising with my peripheral device. Whitelist is being...
Hello,
I am trying to merge the code of ble_app_buttonless_dfu with the code of ble_app_uart,
because I starts all implementation with the code of ble_app_uart at first...
Hello,
I am using SDK9.0 and testing the LED_Blinky project with IAR tool, Evaluation kit. The application is executing and leds are blinking but I am not able to set a...
Hi, and thanks ahead for the help. I am working on receiving ble packets without using the soft device. I am able to transmit an advertisement with raw radio and pick it up...
Hi,
I am trying to write and update a record in flash but not receiving event callbacks FDS_EVT_WRITE and FDS_EVT_UPDATE. I found that i need to add the following code...
Hi there
Is there any PCA10040 simple demo IAR project? Just like print out "hello world" from any debugging uart? Base on this I can add in more functions gradually. ...
I am using clock signal from external RTC chip to clock NRF52832 at 32768 Hz through XL1 leaving XL2 floating. I have verified the waveform by the oscilloscope and set SRC...
