Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Hi,
How can I share a GATT server profile constructed on nRF connect for PC with nRF connect for Android ?
'Save/Load setup' on Windows PC stores/Load json file
In...
I've got a set of boards that are behaving very strangely. I attempt to turn on the HFCLK but the HFCLKSTARTED event never comes nor does the HFCLKSTAT register indicate that...
I cannot suffer this tool anymore. As u can see in the pic below, it provides a cursor mode to measure the currents of X1/X2. However, users always need to know the average...
Hi,
I want to connect 4 antennas to nRF52832, they respectively points to North, South, East and West direction.
Also I hope the nRF52832 can do switch antenna job,...
I'm trying to use gcc and eclipse but I'm getting an error in eclipse that certain variable names cannot be resolved. I know that its not being able to get the variable names...
Hi,
I am developing a small development board of visiting card size, which is powered from a coin cell. I have two questions,
All i want know is there any polarity...
Hi,
do sd_flash_page_erase or sd_flash_write provide any guarantees that the command has executed successfully or should I do a manual check to verify if the page was really...
Hello all,
I am working on nrf52832 Board and i want to use it as translator to send and receive the data , please tel which pins i need to select as UART(rx,tx) pins ...
I am designing a custom board with nRF52840, powered by USB, no battery, using its internal LDOs to supply other peripherals with 3.3V
I have two questions about pins/outputs...
Hi
I generate a pwm signal via changing the state of one characteristic. In general, the pwm works fine. But the problem occurs when I add the timer which is responsible...
Hi guys，
I use the 51822's PWM recently, PWM is made by GPIOTE+PPI+TIMER, and the PWM source code as below(I use TIMER1, GPIOTE[0], PPI_CH[0], PPI_CH[1]， period and duty...
Hi all, I'm asking on both BLE specification version 4.0 (or more) and NRF51822 S130 about having support for multiple central connections at the same time while our NRF51822...
Hi,
I get RSSI values like -96 or -97 dBm before the coded PHY connection between two nRF52840 pdks drops. Are these values something expected? TI advertises sensitivity...
Hi, there~ Nordic's Mesh SDK is fascinating! I was thinking of a way how to connect the Internet with Nordic's Mesh devices.
From the web, you might have seen these...
Hello,
I'm working with the thread v0.10.0 sdk release and I would like to customize and add some new packages to the border router.
I see that there is a release tag...
