Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Hi,
i tried to send data from ios 7 via tx_characteristics(like in UART example) but received error:
didWriteValueForCharacteristic 2A38 error = Error Domain=CBErrorDomain...
I have been trying for a few days now to get my environment setup for development with the nRF51822. Since there is no official configuration for the Mac w/ Eclipse I have...
Apologies if this has been asked before but did search for 'format' in faq and got nothing.
I have been answering to questions.
In my answer I place hard empty lines....
Hi
i use nrf51822 s110 "hrs" example to transmit the data to ios.
I need to add an option to send back some data (from ios to nrf51822). 10 bytes maximum .
how can i implement...
Hi
i use the hrs example to transmit the data to ios.
but i need to add an option to send back data (from ios to nrf51822). 10 bytes maximum .
how can i implement...
Hello,when i get connected to the phone,when i call err_code = ble_hts_measurement_send(&m_hts, &simulated_meas) and err_code = ble_bas_battery_level_update(&m_bas, battery_level...
Hi Nordic, I come from this question: devzone.nordicsemi.com/.../
So, my doubt is: what events are triggered in a slave channel while it is not communicating to a master...
good time dear Engineers!
Please explain how to use correctly HANDLE RANGE in functions of discovering.
I use CENTRAL with up to 8 possible connections to PERIPH, so pls...
Folks,
Have a very puzzling problem (which means I must have done something really silly :-)
Built a prototype in which the nRF52 section is a clone of the one in the...
Hi,
My team has created a custom board with NRF 52 and were able to flash the blinky sample successfully. The LED connected to P.20 is glowing on the custom board after...
Hello! I need to start a sequence of 26 pulses after getting low level signal on gpiote pin.
I can do it in gpiote event handler but I need it most of the time so I want...
I've been developing an application using the NRF52 DK and everything has been going as planned. I then made my own PCB which would take these modules by Rigado. The BMD-300...
Hi,
I am creating an application based on ble_app_hrs_c (central role). I have a few questions on this.
o I do not understand whitelist_load(). It first gets a list...
Good morning Nordic team,
I was measuring the nRF52832 chip in DC/DC mode. Everything went just as expected.
Now I was looking at the current consumption when the radio...
Hi guys. I have a EVK_NINA_B1 board which is based on nrf52832 and SDK12. I am trying to run the ble_peripheral/ble_app_uart/ from examples. I can send message through "nrf...
Hello,
I use SDK 11 with nRF52, softdevice s132.
I am able to successfully use the bootloader in serial mode (with UART) to upgrade the application, but an error occurred...
hi nordic,
After i received this kit from Mouser Electronic, when i got it check the board which some question,
we examined its outward appearance and found that this...
Hi,
I have my nrf52 DK. I would like to advertise as Beacon and be BLE (which I can connect to via iOS app) device at the same time. Do you know any examples of this kind...
Why does the macro CHECK_RAM_START_ADDR only check for C_LINK_CNT and P_LINK_CNT and not the SEC_COUNT? It is always set to 0 in the macro.
I have increased the central_sec_count...
Hi ，
I use timer to handle pwm signal,
1.when calling button by phone is pressed,
Timer starts,(function:on_key_trig_speaker_event())
2.pwm signal run (speaker_meas_timeout_handler...
