Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
I have a program based on some of the examples which runs in peripheral and observer roles. When either role is running alone it works without issue but if advertising and...
Hi,
my task is to develop a "repeater" and I have three nRF51422 evaluation kits.
For example, one of them sends a file, the second one receives it and then sends it to...
Hello,
Using the "simple_uart_get_ with_timeout",I cannot receive a "frame" bigger than 6 bytes.
Why?
while(simple_uart_get_with_timeout(1, &UART_RX[receivedBytes]...
I have a simple app that send button press/release events to a smart phone. One of the buttons doubles as the wakeup button. I would like to qualify the wakeup button press...
The documentation for S110 v7.1.0 sd_nvic_ClearPendingIRQ implies that it works with any valid IRQ.
I find that (using S110 v7.1.0 with SDK 7.1.0):
sd_nvic_ClearPendingIRQ...
Hello,
I'm currently reading nRF51_Series_Reference_Manual_v2.1.pdf. On page 28.9.9 there is the UART CONFIG register documented. Two bits of configuration for the Parity...
Hi,
Tried to develop an application to read current time characteristics from central device (ios app) by using nrf51822 peripheral device(s110_nrf51822 v7.0.0.). After...
Dears,
There is a problem as the subject. I am using the reference code of ble_app_hts to add an app timer for a service. the device of nRF51822 can be searched and connected...
Hi,
I'm really new here, sorry if it is a beginner question.
Our company wants to start developing a RTLS (Real Time Location System) to track mainly person (patients...
There are a few threads on using the AES module and there is a lot of confusing and somewhat contradictory information.
I want to do the following:
generate secure...
Hello,
i have an application that sends periodically sensor data from one sensor network (6 sensors - 16 Bytes) to a host f = 1/4 - 20 Hz.
I read the s210 and s110 SDS...
Hello, I'm using the nRF6310 board and tried the HID Keyboard Application
(S110, ble_app_hids_keyboard) example.
The nRF51 SDK version is 6.1. I use IAR for ARM 7.1. ...
Dear,
We are developing the nRF51822 for an application of BLE device. The timer is the key process in the application. Anyone kindly share the experience with me about the...
I have a test set up using the ble_app_hrs example where I increment a dummy uint16_t periodically and then send that value up to the nRF Toolbox iOS app to plot. I want to...
