Hi everyone,
I'm using the nRF51822 (pca10000 Dongle + pca10005).
My plan is to send one byte over the radio.
I tried to use the SDK-Example as a template but it's...
Hi,
Is that possible to run the radio_test_example (\nRF51 SDK_v5.2.0.39364\Nordic\nrf51822\Board\nrf6310\radio_test_example) on the nRF51822EK? If yes, what modifications...
we also produced self PWM for ADC wave form testing. when we stop transmission, we will get good waveform out, but when we starting transmission, output waveform shape is...
Dear Support,
I have some troubles with the Evaluation Kit for nRF51822 :
I use the broad as a central role with S120_nrf51822_1.0.0_softdevice.hex and example...
Suppose a nRF9E5 transmitter is set for continuous transmission on a channel.
A nRF9E5 receiver listening on that channel:
finds carrier and sets CD
finds address...
I will be deploying my nRF51822-powered devices into the field and the end user will not be able to have any physical access to, for example, power cycle the board. I need...
I have procured nRF52840 Dongle and i followed the instructions as mentioned in the link https://infocenter.nordicsemi.com/pdf/nRF52840_Dongle_User_Guide_v1.1.pdf and i am...
Hi,
I'm use the Anritsu 8852B that be production flow.
My hardware setup is OK that be verifyied by DTM tool.
" Bluetooth low energy Measurement Software " always show...
Hello,
I am using nRF52840 with our custom board. In that, I am implementing the DTM firmware for test radio.
I was able to receive packets but when I try to read the...
Hello
I would like to protect some Bluetooth characteristics in order to protect them from eavesdropping.
In fact, here is my problem: I would like to make an application...
Hi all,
I am calling arm_rfft_fast_f32 which uses the FPU on the nRF52840.
Unfortunately when I disconnect from BLE connection and stop advertising, the consumption remain...
Hi There,
I was wondering if anyone had any insight into whether the OTA-DFU (Android/iOS) LIbraries can be integrated into a Unity application? Is it possible to combine...
Hi,
I've defined a base uuid 455449424C5545544845524DB87AD700
For adding the service to the database CUS_SERVICE_UUID = 0x4942 which alters my 12th and 13 octets
Instead...
I have a characteristic that i want to change to allow notification.
But when I include the presently commented line below (that sets notify to 1), the code breaks, which...
We have a prototype device that disconnects and reconnects frequently. When moving from a BLE 4.2 chip to the nrf52840 (BLE 5), we noticed that the time to complete the initial...
Hello,
I am developing a project with a host processor and Minew BT module with NRF52811. The module and the host processor are communicating via I2C (TWIS). The host processor...
Hi,all
As said above, i've tested two laptops, and this situation happened. I have no idea why this will happen. Is there may any problem with the c onnection parameters...
I used stm32 as master and nordic board as a slave , in stm32 i used spi2 where my configuration is , baud rate is 4MBits/s , clock polarity high , clock phase 1 edge and...
I am trying to locate documentation that has recommended solder paste and reflow specifications for the QFN package. I see there was a similar request made quite some time...
Hi,
When looking at the release notes for the latest nrf9160 modem firmware, it says that the B0 devices are for development only, and B1 for production. I have a number...
Hi there!
Back again with another question. Now that I've finaly managed to get the Bitmap image to show on the display (ST7735), I noticed the playback of audio from the...
