Suppose a nRF9E5 transmitter is set for continuous transmission on a channel.
A nRF9E5 receiver listening on that channel:
finds carrier and sets CD
finds address...
I will be deploying my nRF51822-powered devices into the field and the end user will not be able to have any physical access to, for example, power cycle the board. I need...
Hi,
We are using the ble_app_uart example in evaluation board to read data from some sensors and send it to the nRF UART V2.0 in Android 4.4. Every 20 ms I am trying to...
I am try this at nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
Firt I connect to Android device and keep one whitelist.pp_addrs and one whitelist...
Hi,
Parameter uint8_t ble_gap_scan_params_t::filter is present in the documentation, but not implemented.
Checked for SDK 5.2.0 and 6.0.0.
devzone.nordicsemi.com...
After I get a Disconnected() event, I want to start scanning again, therefore try to call StartDeviceDiscovery() again.
IsDeviceDiscoveryOngoing was checked before.
The...
Hi there,
I have been testing my ble long range app with coded phy (s8), with extended advertising etc. for a few weeks now. Only adv and scan are used. Works well, only the...
Hi,
I'm using SDK 15.0.0.
I'm trying to run part of TWI example in my project in separate .c file.
But I have next error:
Error[Pe020]: identifier "NRF_DRV_TWI_INSTANCE_0...
Hi,
I know that the BLE protocol allows to write up to 20 bytes size packets, I have also set max length to 20 bytes in my custom characteristics.
But when I am trying...
Hello,
For OTA updates or DFU I want to create a zip file that contains the Bootloader, Softdevice, and Application into one, But when I generate this through nrfutil.exe...
Hi all
I am using S130 SDK12, nRF51822
This is the error I am getting - line_num 0x07C0, p_file_name 0x06D1, error code 0x00D1, fault id 0x0001, pc 0x83CC (a print-screen...
From Mesh Model v1.0.1 section 3.3.5.1 Generic Power OnOff Setup Server
"This model shall support model subscription, as defined in Section 4.2.3 of the Mesh Profile specification...
Hello Nordic!
I need to save dynamic arrays in NRF52840 flash using FDS, but after some days of trial and error I need to beg for help.
What I need to achieve is to have...
I'm trying to enable TWI in the eddystone example based on this article but I get the following compilation error:
nrfx/legacy/nrf_drv_twi.h:120:37: error: 'NRF_DRV_TWI_INSTANCE_0...
Hello,
I'm using nrf52832, sdk17 and Seeger Embedded Studio. I am using ble_app_uart example.
I am connecting with my phone and using RX and TX characteristics. My question...
Hello !!
I want to use Radio transmitter/ receiver example in my custom board which is used for BT remote control battery powered. I have added 10 buttons on my board and...
Hello NRF team,
We have been using NRF52832-QFAA based dev kit from Sparkfun, which has 512KB Flash / 64KB SRAM. I developed the app on Arduino whereas I flashed the bootloader...
Hello!
Here is a story I am sure you have heard before. I am evaluating the NRF9160DK and seeing what is the lowest power consumtpion we can get when sending data to a server...
I have an existing product using the nRF52832 SoC rev 1. We must transition to rev2 since rev1 is no longer sold. We use SDK12.0.0, with S132 V3.0.0. Have these software components...
