I posted another question along these lines, about using the Timeslot API to get observer behaviour with the S110 v7.0 SD, but I am having trouble getting it to work.
Are...
I'm interested in creating a time of flight algorithm and am trying to calculate what to expect for accuracy.
Is it possible to get an IRQ from when the sync arrives at...
hi all ,
how to enable GPIOTE PORT and IN[n] event simultaneously ?(not same pin)
i enable the GPIOTE to trigger interrupt event.
one for the keyboard which need multiple...
Hi All,
I am using nRF51422 with softdevice s310. And implementing Cycle speed and cadence receiver. most of the data processing is fine but i am facing one problem.
...
Hello Nordic Team,
I have a problem with programming the nRF24LE1 chip.
I am developing a small system, which consists of a uC STM32F4xx and a nRF24LE1 Radio Module. The...
Hi,
I'd like to learn about the app compatibility for the new OTA DFU that ships with the new SDK 6.0.0 and S110 7.0.0. I am using a nRF51822 board and I've observed that...
I have a custom nRF52832 board with outputs on P0.07 P0.08 P0.09 P0.10 and I want to write to them. 7&8 are working ok but 9&10 are not.
Let me emphasise THE BOARD IS WORKING...
Dear Nordic and community,
I am currently in pre-production phase of designing a PCB based on the NRF9151, and I am a bit confused by the Hardware Device Guidelines, which...
Dear nordicsemi,
In our application, we need obtain the number of input edges,but we always get a incorrected result in a long-time testing situation (2-3 hours), and this...
Hi Nordic engineer
I am evaluating a project based on nRF52840 and there is a question need to be confirm before schematic design start.
Due to limitation of power resource...
Hello
I'm new with zephyr environment and I want to use littlefs in order to partition an external flash over spi, and to be able to upload file over BLE by using a SMP...
Hi, We are currently working on a new product based on NRF54L15. Goal : We are trying to set up the "Bluetooth LE UART service" example in order to transmit and receive data...
Hello everyone,
I'm trying to set up the Wifi stack on the nRF7002 and use it with MicroPython, but encountering a lot of difficulty with it. I cropped up a network_wlan...
Hi all,
I have a custom board build with an nRF9151. I'm able to connect on int with USB/UART, I can send and receive AT command. Right now I'd like to send certificat to...
My application communicates via UDP and all communication is initiated from the device. Before packet transmission, network registration status is checked (CEREG) and sendto...
Hello, I'm developing a BLE Central application using the nRF52 SDK. The central connects to multiple peripheral devices (nRF52832), each sending 6-byte ADXL345 accelerometer...
Hi All,
I came across this thread regarding programming external boards. ( https://devzone.nordicsemi.com/f/nordic-q-a/14058/external-programming-using-nrf52-dk )
In order...
I discovered weird modem behavior when testing my application with a weak or undetectable signal. Mine testing was as follows:
modem connected to the network
communication...
Hello,Nordic team
I am programming with nrf52833 and ncs v2.9.0
While bonding with peripheral ,central report No memory to create new report.But my soc flash and ram are...
I work on nRF54L15DK.
When building for the nRF54L15DK, only 188KB of SRAM is allocated. The remaining 68KB seems to be allocated to the FLPR MCU. How can I change this...
I have already written the factory data to the device, and commissioning via Apple TV is successful.
It also works when using the --bypass-attestation-verifier 1 parameter...
