Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
I have 3 nordic boards each having different serial no so i need to develop a a structure with the information of the serial no and some revision number etc
and i need to...
hi everyone,i have a problem when i want to esase one block of flash memery,if i do it before ble_stack_init,it can work,but if i do it after ble_stack_init,my program will...
Hi,
We have made a custom PCB using the NRF52832 chip. While it was working fine for a couple of days, it suddenly stopped working and went to a hard fault. We are not...
hi:
i have a problem when i want to write data to flash.by the way,my program is running with no-system.
i found the program is always restared when i enabled erasing,
...
I was testing ble_app_uart with my nRF51 DK and gcc compiler on Mac OX. Everything went fine. But after blinking for about 1 minute, the light that was supposed to be blinking...
Hi,
I found my debug session keeps reset due to this error (code jump into app_error_fault_handler) when I stepped through my code. This happens at random places. I'm not...
I'm trying to get the nRF52 on the PCA10040 dev board communicating through UART without the use of the programmer built into the dev board. So I'm connecting the UART pins...
Using the ble_app_uart example, if I pass more than get a maximum of 60 characters for each call to ble_nus_string_send I get a return code of NRF_SUCCESS, but the nRF UART...
Hello, we use an MDBT40 Module from Raytek with an nrf51822 chip.
We take this module for building a ble remote control.
The remote control is central and the receiver is...
Hello,
I Try to use nRFsniffer 1.0.1 on windows with Wireshark 2.0.1.
Wireshark seems to crash at startup. (reported bug 12103 on wireshark bugzilla)
Please provide...
I'm hoping someone here is familiar with the VL53L0X setup on a NRF52 board. I was able to get the single range measurements working just fine using polling and now I want...
I am using the PPK with SW v1.1.0 on a windows virtual machine on my mac. I'm testing custom hardware using the PPK regulator to supply power to my hardware.
There seem...
Maybe I understood something wrong, but I wonder if it is possible to have the nRF52840 handle file transfers like it does with the firmware hex-files.
Say, I want my nRF52840...
I am facing some issue, I am using HM10 ble module as peripheral and NRF52832 (Redbear NANO v2) as central device. I using SDK "nRF5_SDK_12.3.0_d7731ad" and example program...
