I'm trying to use the ADC and internal reference to measure battery voltage on the nrf51422, while S210 is enabled.
From the example nrf51-ble-app-temp-master, I found...
I have Nokia Lumia 630 and it works well with nRF51822-EK but only with SDK nrf51822_v5.1.0.36092 and SoftDevice 6.0.0. Now I decided to try DFU OTA. I programmed bootloader...
Hello,
I found that there is a multiprotocol demo in folder Board\nrf6310\s110\experimental\ble_app_multiactivity_beacon,then I found it can implement concurrent connected...
Dear Sir
We got the problem on DFU upload firmware, it always failed in second DFU . We must unpair the device at iOS setting panel. Before next DFU.
Here is the log data...
Hi All,
My requirement is to read the data from nRF51822 device that is connected to a bluetooth and bluetooth is connected to a system using a .Net application.
I have...
Hi everyone,
I'm using the nRF51822 (pca10000 Dongle + pca10005).
My plan is to send one byte over the radio.
I tried to use the SDK-Example as a template but it's...
Hi,
Is that possible to run the radio_test_example (\nRF51 SDK_v5.2.0.39364\Nordic\nrf51822\Board\nrf6310\radio_test_example) on the nRF51822EK? If yes, what modifications...
We have been manufacturing for a while with the nRF51822, Revision 2, and WLCSP package and build code D0 (D0 is what Nordic recommended me to spec to contract manufacturers...
Hi all,
I have application that read analog level and send the data with connection interval of 10 ms and 0 dBm, how can i calculate the current consumption of BLE? i read...
Hi
I want to use Printf() in the DT2 but it cannot output msg to terminal.
I used hal_uart_config() to config UART TX/RX/Baudrate... in mail.c then
call hal_uart_put_str...
I use S110 V7.1.0,nrf51822 chip,
now I need write and read flash data in BLE mode.
When can I write the flash data at BLE mode?
When can I read the flash data at BLE...
I'm calling the requestData function and lib_aci_close_remote_pipe at the same time.
The lib_aci_close_remote_pipe returns 0x8E command error which means: "Command rejected...
Hello,
I need to store some app configuration on the FLASH and I'd like to use the features of pstorage module.
I don't understand the following thing ...
When the...
Hello,
I am currently using the SDK setup from this URL: embeddedsoftdev.blogspot.de/.../ehal-nrf51.html
In order to use that setup, one must change a line in the file...
Hello,
I downloaded MDK arm from Keil website (keil mvision 5), SDK and MDK pack from nordic download site. After installing SDK, I am not able to find example projects...
Hello,
I have quite a few of setting on my nodes and I want to save some of these permanently. Currently I am using the pstorage module and everything works as expected...
Hello everyone,
i can able to set the static passkey but i would like to know the difference bewteen security key and passkey how can i set security key ? any suggestions...
Good day!
Faced with the problem that I didn't get to run N5 Starter Kit (nRF51422) on maximum speed in Advanced Burst Mode, using ANTware II with ANTUSB-m to read packets...
I read the multi-role project on Github. For time slot part, there's no explicit hfclk start/stop operation along with the radio events, is it possible that sd_radio_session_open...
In the nRF8001 Arduino SDK, there is a " ble_bandwidth_test " example.
It says,
"The bandwidth is measured (sic?) with the nRF UART App in the Apple iOS app store" ...
I am trying to communicate with a SPI peripheral, using the nRF52 as the master, and the peripheral as the slave. What happens is that it still faults out, and the presence...
