I will be deploying my nRF51822-powered devices into the field and the end user will not be able to have any physical access to, for example, power cycle the board. I need...
Hi,
We are using the ble_app_uart example in evaluation board to read data from some sensors and send it to the nRF UART V2.0 in Android 4.4. Every 20 ms I am trying to...
I am try this at nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
Firt I connect to Android device and keep one whitelist.pp_addrs and one whitelist...
Hi,
Parameter uint8_t ble_gap_scan_params_t::filter is present in the documentation, but not implemented.
Checked for SDK 5.2.0 and 6.0.0.
devzone.nordicsemi.com...
After I get a Disconnected() event, I want to start scanning again, therefore try to call StartDeviceDiscovery() again.
IsDeviceDiscoveryOngoing was checked before.
The...
Hi, I wanted to ask a question regarding sending data.
I currently have external memory that will send out serial data (SPI) to the nordic microcontroller. I have saved...
Hi
We have a product that we are preparing for production.
The product needs to communicate with an Azure IOT Hub that only accepts RSA keys. We have used the device_credentials_installer...
Hi,
So we are currently using modem firmware nrf91x1_2.0.2 on a custom HW. I keep getting this error during boot and only after I wait for 30 mins I can connect to my...
Hello, I am developing with nRF5340 with my custom board. I observed a high current consumption when the network core is flashed with the ipc_radio image. I am developing...
Hi I want to use nRF9151DK and i have jio NB-IOT sim card.
I flashed asset tracker application from quick start and it is not working or connecting to internet this is the...
[Environ] nRF Connect SDK v3.2.3 nRF9151 (Custom board) VSCode (1.115.0) Board target: board/nrf9151/ns
When using the PTI firmware, the AT command resulted in an error...
I have a PCB with nRF52833 and nPM1304, I assembled 3 identical PCBs, 2 of them work 1 does not I am using 2 available Buck coveters, first outputs 1.8V for powering IC on...
Hi,
I a\m looking for your recommendation on screen to use with nRFLM20DK board to experiment with LVGL display. Assuming that latest version of nRF Connect SDK has everything...
Hi,
I am using nRF5340 (CPUAPP) with MCUboot and Partition Manager (pm_static.yml, CONFIG_PARTITION_MANAGER_ENABLED=y ).
Build and flash are successful, but during debug...
Dear Technical Support Team,
I have recently been developing with the nRF54L15-DK development board, using the official channel_sounding/cs_test example provided by Nordic...
I am designing a battery system with can charge or supply power via a USB-C PD controller. It will operate up to 20V. I want the option to connect this USB-C D+/D- to the...
Hello, I was able to flash the firmware built using the samples provided by the "nrf connect sdk" using VScode. But, I see failure when I tried to program the nRF54L15 with...
When the USB stack and your local Filesystem code both try to control the flash chip simultaneously, the system will crash or trigger a HardFault, causing the restart.
Dear Nordic,
I have a few questions I would like to ask.
1. I would like to inquire if there is an antenna pattern for the nRF54L15DK PCB.
I have already searched through...
I was trying to flash a program on nRF52833 development kit and got this error, it important to notice that my college was trying to flash (via VS code) it before and I am...
Hi,
I'm working with the nRF54LM20 DK (nRF54LM20A) and evaluating whether it can act as a USB host to read data from an external USB CDC ACM device.
The intended setup...
