After I get a Disconnected() event, I want to start scanning again, therefore try to call StartDeviceDiscovery() again.
IsDeviceDiscoveryOngoing was checked before.
The...
Hi, I wanted to ask a question regarding sending data.
I currently have external memory that will send out serial data (SPI) to the nordic microcontroller. I have saved...
Recently, I try to programme nRF51822 DK communicating with nRF2401e1 DK,unfortunately，which does not success. With setting radio configuration: TXPower,frequency channel...
E:\BLE\work\nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
SDK 6.0.0
Softdevice 7.0
When I connect to Android 4.4.3 device(Nexus7 II) will...
E:\BLE\work\nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
SDK 6.0.0
Softdevice 7.0
When I connect to Android 4.4.3 device(Nexus7 II) will...
I have been trying to understand and get the “ble_app_template” running this weekend, but I keep running into errors. For example in
static void sys_evt_dispatch(uint32_t...
Based on the nRFUart demo, I added a masterEmulator.DiscoverServices() block before the DiscoverPipes() block in a very similar manner. Purposed is to be able to get more...
After attempting to write data to the filesystem, my 125μs timer interrupt (highest priority) is delayed by tens to hundreds of microseconds.
I enabled the following configuration...
I'm having a hard time replicating the config needed to be DFU compatible with a build from an earlier SDK version. Earlier version used only a non upgradeable MCUBoot with...
Hi,
I am working on the channel sounding procedure with the nrf54l15 dk's right now and I have an external antenna that I want to use to improve the connection. I plugged...
On nrf-sdk 3.0.1, we were running nrf54 (main app) with Zephyr's PPP modem for nrf91 SLM. Everything was working fine. After upgrading to nrf-sdk 3.1.0, I am now getting this...
Hello Team,
I am currently working with the nRF52832 and using the nRF Connect SDK ( NCS) with toolchain version 2.9.1. I would like to interface the nRF21540 RF Front-...
Dear Nordic Specialist,
I am currently testing the minimum connection interval at which BLE Channel Sounding can operate reliably. Specifically, I would like to achieve...
Hello,
I was wondering if anyone would happen to have sample code to activate the accelerometer in the Thingy 91X? If also possible, it would be very helpful to have the...
I'm trying to setup some code to emulate an NFC tag with an NDEF external record based on the NFC tag sample in NCS 2.6.0.
The hardware is a custom board based on the nRF52840...
Hello I am investigating the power consumption of the nRF9151-DK using PPK II. The measurement settings are as follows.
・Connect PPK II's VOUT and DK's P22 VDD_nRF. ・Connect...
I use nrf5340 audio DK, SDK v3.0.2, and added an iso.conf,
A lot of warnings were reported during compilation.
Are these conf not effective?
If I want these conf...
I'm interested in configuring a NR5340DK as an end device on a Zigbee network where the coordinator is a 3rd party device that uses legacy Zigbee. I'm fairly new to Zigbee...
Hello. I'm trying to call an interrupt service routine (ISR) using IRQ_DIRECT_CONNECT, but it is not working.
Here is the flow of my code:
So, it is expected to print...
Hello,
I am adding security feature for BLE in nrf52810 custom board. I am using v2.9.1 toolchain and 2.9.1 sdk files
PFA BLE related file as well as .conf file as well...
What is the quiescent current of the PM1300 when it is not in SHIP or hibernate mode, but when it is "alive" and configured and running off the VBAT terminal, ignoring any...
Hello, I’m working with a custom board using nRF7002 + nRF5340 + MX25R64 (SPI4) , and I’m trying to perform firmware updates over Wi-Fi using a firmware file hosted on an...
