I am try this at nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
Firt I connect to Android device and keep one whitelist.pp_addrs and one whitelist...
Hi,
Parameter uint8_t ble_gap_scan_params_t::filter is present in the documentation, but not implemented.
Checked for SDK 5.2.0 and 6.0.0.
devzone.nordicsemi.com...
After I get a Disconnected() event, I want to start scanning again, therefore try to call StartDeviceDiscovery() again.
IsDeviceDiscoveryOngoing was checked before.
The...
Hi, I wanted to ask a question regarding sending data.
I currently have external memory that will send out serial data (SPI) to the nordic microcontroller. I have saved...
Recently, I try to programme nRF51822 DK communicating with nRF2401e1 DK,unfortunately，which does not success. With setting radio configuration: TXPower,frequency channel...
E:\BLE\work\nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
SDK 6.0.0
Softdevice 7.0
When I connect to Android 4.4.3 device(Nexus7 II) will...
E:\BLE\work\nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
SDK 6.0.0
Softdevice 7.0
When I connect to Android 4.4.3 device(Nexus7 II) will...
Hello,
given that the Micro:bit V2 (Nrf52833 based) has been promoted in Webinars, I am surprised on the lack of enthousiasm in getting it to work properly under NCS/Zephyr...
Hi
I checked how AT%XOPNAME could be used to receive notifications about operator name updates. However I'm wondering about the notification syntax.
According to the specification...
https://infocenter.nordicsemi.com/index.jsp?topic=%2Fcom.nordic.infocenter.meshsdk.v5.0.0%2Fmd_examples_sdk_coexist_ble_app_uart_coexist_README.html&cp=8_2_3_3_1
In this...
Hi,
I developed some multi peripheral units. and also i developed some central units which are allowed to connect to the multi peripheral devices.
F.E: i got 2 multi peripheral...
dear all
I use nrf52840 to compile a library with floating-point operation. I configured it in my *. Conf
CONFIG_ FPU = y, but we can't find sqrtf, sinf, logf and so on...
For a customer I am developing a Zigbee coordinator / Gateway with the nRF52840. As software basis I use the “Zigbee cli example” from SDK V4.1.0.
So far, everything works...
I installed nRF Connect SDK v1.6.0 and SES Nordic Edition through the nRF Connect toolchain manager (Windows 10). I'm finding that I can't use the "open nRF Connect SDK Project...
Hello,
I'm trying to make the RF frequency of TX channel configurable.
I have noticed that anything higher than 0x50 is not acceptable for sd_ant_channel_radio_freq_set...
Hi,
I wanted to use the console on nRF52840DK in high-speed UART mode (921600bps) but it fails and I just saw the DK User Manual says:
Baud rate 921 600 is not supported...
I'm using the ble_nus_c NUS client code for a custom 1:1 data link between two embedded nodes, just pinging a few bytes of data back and forth every 3 seconds. Bonded connection...
Hi,
We are using nRF52840 SOC with our custom board . Due to some reason, the SWD data line( SWDIO pin ) shorted .
So now we are looking into how we can program nRF52840...
From SDK we can see that there is a lot of events about security. I've read some of them by comments and still a little confused about the difference of them.
Could anyone...
We're using the Azure iot hub implementation in a custom product that works with Azure.
One of the things we've noted is that if the total size of the device twin exceeds...
Hi,
I'm using nrf52840 in order to connect to a mobile and PC.
When connecting to a mobile, connection is bonded, but when connection to a PC, it's not, although m_sec_param...
