Hi,
Is that possible to run the radio_test_example (\nRF51 SDK_v5.2.0.39364\Nordic\nrf51822\Board\nrf6310\radio_test_example) on the nRF51822EK? If yes, what modifications...
we also produced self PWM for ADC wave form testing. when we stop transmission, we will get good waveform out, but when we starting transmission, output waveform shape is...
Dear Support,
I have some troubles with the Evaluation Kit for nRF51822 :
I use the broad as a central role with S120_nrf51822_1.0.0_softdevice.hex and example...
Suppose a nRF9E5 transmitter is set for continuous transmission on a channel.
A nRF9E5 receiver listening on that channel:
finds carrier and sets CD
finds address...
I will be deploying my nRF51822-powered devices into the field and the end user will not be able to have any physical access to, for example, power cycle the board. I need...
Hi,
We are using the ble_app_uart example in evaluation board to read data from some sensors and send it to the nRF UART V2.0 in Android 4.4. Every 20 ms I am trying to...
I set up PPI so that it kicks off TWIM (I2C) transfer on GPIOTE pin transition low to high. Everything works great, except that I also setup a fork task to set another GPIOTE...
Having a BUS FAULT while trying to use uart_tx on the NRF5340 with NRFConnect SDK. Based on the peripheral_uart sample project. Any ideas what may be causing it?
Heres...
This took me a while to figure out.
The default values for the WDT configuration in SDK 15.3.0 (and 16.0.0) is spelled as "NRFX_WDT_DEAFULT_CONFIG" ?
RMV
The following code has an unexpected out-of-bounds array access:
Primary cause is this line:
On an uninitalized pin number, channel_port_get() returns -1, which...
Firstly my current usecase:
We are using a STM32 as a main processor. the STM uses UART to communicate with the nRF52 using the serialization stuff. I currently have most...
Using ncs v1.4.0, modem FW v1.2.3, SES v5.10d.
I'm trying to get NVS working using /zephyr/samples/subsys/nvs. It is failing to write. I also tried the code in this post...
hi
i was trying to interface sd card with nrf9160 in segger emstudio. i was following the ticket Reading SD card on nRF9160dk - Nordic Q&A - Nordic DevZone - Nordic DevZone...
HI sir i was trying to interface pdm microphone. i followed the existing ticket PDM Driver for Zephyr on nrf52840 . i had modified the proj.conf as below
but during the...
I've created a peripheral that is advertising about every 320ms but am seeing less than half of those packets in nRF Connect on my Android mobile (configured to run in low...
Hi, Could you please guide me on how to fix this? I've ported the slm client example here to the bsp project inthe sdk and getting this `.nrf_queue' will not fit in region...
I have an input signal of unknown period and pulse width on a GPIO. I want to use the PWM capture capabilities to retrieve those parameters.
I see in the documentation there...
In my quest to gain access to the nor memory on the nrf9160-dk I have found what happened to the WP and HOLD signals and now external_flash_pins_routing configuration setting...
Hi,
When I plug in my NRF51 Dongle it shows up in Windows explorer as additional drive (JLINK). Can I use this medium to configure my application? Can I read a file pun...
Hi,
I have a small pcb project with low power bluetooth IC NRF52832. There is a limited space on PCB so i decided use the 2.4 GHz chip antenna. İs there recomended chip...
