E:\BLE\work\nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
SDK 6.0.0
Softdevice 7.0
When I connect to Android 4.4.3 device(Nexus7 II) will...
E:\BLE\work\nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
SDK 6.0.0
Softdevice 7.0
When I connect to Android 4.4.3 device(Nexus7 II) will...
I have been trying to understand and get the “ble_app_template” running this weekend, but I keep running into errors. For example in
static void sys_evt_dispatch(uint32_t...
Based on the nRFUart demo, I added a masterEmulator.DiscoverServices() block before the DiscoverPipes() block in a very similar manner. Purposed is to be able to get more...
Hi,
There is much talking about the "large data transfer" over BLE, the l2cap channel being the best option for the moment.
However, does anyone know the datarate achievable...
NRF24AP2 with MSp430F149 . ASYNC 9600 N 8 1
step 1 : reset NRF24AP2 with reset pin , and received a pulsing signal through RTS pin
step 2: send a char (0x4A) to NRF24AP2...
Hi guys,
I am using the gcc setup to program my boards. However for flashing the softdevice I use nrfgoStudio. SO I downloaded the hex file and fashed the siftdevice. But...
nrf5 SDK 15.20
Mesh SDK 3.0.0
nRF52832
Hi,
I am using nRF52832 and mesh stack , i want deliver temperature data through Mesh network.I look and run light-onoff &...
Hi Folks,
I would like to configure an UART RX pin as input GPIO as well as keeping it as dedicated to the UART peripheral.
I would also like to know if I can configure...
Using the current nRF connect v3.6.1 Getting Started Assistant I've managed to get everything installed to the point of using west to install the complete nRF Connect SDK...
This thread discusses the nrf51 devzone.nordicsemi.com/.../current-consumption-when-using-rtc-ppi-and-gpiote It says that the PPI (for nrf51 chip revisions up to rev 3) keeps...
Hi,
What is the used coding scheme in nRF Connect for Mobile when advertising on Coded PHY? Is it S2 or S8?
Should be clarified in the screen below
Thanks,
Lu...
In this PDF: https://infocenter.nordicsemi.com/pdf/nwp_037.pdf
On page 28 it says:
Active components on the PCB cause wideband noise coupling to the antennas. Verify that...
We have designed a board using the nRF9160 SiP and LWM2M. When testing with poor network connection (~ -118dB) we experience a strange behaviour. From monitoring the current...
Hello,
I have tested secure_bootloader_ble_s132_pca10040 project with Segger Embedded Studio. it works fine and I can update my application.zip via nrfConnect android application...
I cannot get OTA DFU to work on a tablet I have, it works fine with my phone but does not start the transfer, then drops out and reconnects?
Same board, same zipped package...
Dear friend I checked the data sheet of 52820 and I didn't see any LPCOMP peripherals. Check the data sheet of 52832, there are LPCOMP peripherals. Comparing COMP and LPCOMP...
My nrf9160 isn't responsive to the AT commands for MQTT mentioned here . I want to know why is that so? I've put certificates in the module from AWS-Iot core and flashed at_client...
I'm attempting to use nrfutil with a nRF52 DK to perform dfu over BLE. The command I'm using and the result I get is:
This is with the latest nrfutil 6.1.0, on windows...
Hi,
with the tool BLE Sniffer we see a lot of useful informations. There is also a item called Pakettime. Ist this the meassured time with wireshark or the true time on...
