Suppose a nRF9E5 transmitter is set for continuous transmission on a channel.
A nRF9E5 receiver listening on that channel:
finds carrier and sets CD
finds address...
I will be deploying my nRF51822-powered devices into the field and the end user will not be able to have any physical access to, for example, power cycle the board. I need...
Hi,
We are using the ble_app_uart example in evaluation board to read data from some sensors and send it to the nRF UART V2.0 in Android 4.4. Every 20 ms I am trying to...
I am try this at nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
Firt I connect to Android device and keep one whitelist.pp_addrs and one whitelist...
Hi,
Parameter uint8_t ble_gap_scan_params_t::filter is present in the documentation, but not implemented.
Checked for SDK 5.2.0 and 6.0.0.
devzone.nordicsemi.com...
After I get a Disconnected() event, I want to start scanning again, therefore try to call StartDeviceDiscovery() again.
IsDeviceDiscoveryOngoing was checked before.
The...
Hi,
I am trying to develop an application for Thingy:91, which would allow me getting data from BLE and sending it to the cloud with LTE. I am working on NCS 1.3.0.
Of...
I just tested with the example project, "ble_app_uart" using SDK, "nRF5SDK17009d13099.zip" on nRF52DK (labelled with PCA10040 1.2.4 2018.23) board on Segger embedded studio...
Hi ,
i am trying to interface a WINBOND W25Q64JV flash module with NRF52,i can able to read device id,status register success fully.
i wrote the data in particular address...
Hi,
I'm using nRF52840 DK as a central. Our project is based on ble_app_uart_c example. There is filter for UUID only during scan.
I noticed, that for conection establishing...
I'm using the nrfjprog command "nrfjprog -f nrf52 --reset". This sometimes causes my custom board to hang. I dont think it is able to boot at all, I do not see any uart output...
I would like to ask Nordic to create an example of an Android background service that can detect a device advertising.
Android imposes background execution limits which...
I am using nRF52840, SDK 16 + s140 with segger embedded studio.
I have already added NUS service to my application by taking reference to ble_app_uart example. I want to...
I need to somehow connect 10 i2c devices to nrf52, to do that I need 5 i2c peripherals, but nrf52 has only 2.
I see different options:
1) Use multiplexer. Probably a good...
Hello, support team.
I try to use nRF Connect v3.4.2 on Ubuntu 16.04.6, VMware.
But there is no response after executing specific application eg. Bluetooth low energy...
Hello everyone,
I have problem with a code for reading BME680. Here is my code the values display are wrong and never change.
Thank you for your time. I used this Library...
When adding the DK to my nRF cloud account, I get the following error message: " There was an error adding your device: nRFCode 40102: Ownership code [HWID] is invalid for...
nRF52840, SDK v16.0.0 SD140v7.0.1
Our electrical engineers gave us a hard ATT_MTU limit of 65 bytes, so as to keep the peak current low on the battery for our ultra-low...
Hi,
I'm running into a problem where a TWIM TX call gets stuck internally waiting on the NRF_TWIM_EVENT_STOPPED event. It never breaks out of this while loop in the twim_xfer...
