I have Nokia Lumia 630 and it works well with nRF51822-EK but only with SDK nrf51822_v5.1.0.36092 and SoftDevice 6.0.0. Now I decided to try DFU OTA. I programmed bootloader...
Hello,
I found that there is a multiprotocol demo in folder Board\nrf6310\s110\experimental\ble_app_multiactivity_beacon,then I found it can implement concurrent connected...
Dear Sir
We got the problem on DFU upload firmware, it always failed in second DFU . We must unpair the device at iOS setting panel. Before next DFU.
Here is the log data...
Hi All,
My requirement is to read the data from nRF51822 device that is connected to a bluetooth and bluetooth is connected to a system using a .Net application.
I have...
Hi everyone,
I'm using the nRF51822 (pca10000 Dongle + pca10005).
My plan is to send one byte over the radio.
I tried to use the SDK-Example as a template but it's...
Hi,
Is that possible to run the radio_test_example (\nRF51 SDK_v5.2.0.39364\Nordic\nrf51822\Board\nrf6310\radio_test_example) on the nRF51822EK? If yes, what modifications...
we also produced self PWM for ADC wave form testing. when we stop transmission, we will get good waveform out, but when we starting transmission, output waveform shape is...
Hi, we want the DFU code in SDK 10.0 for NRF51 S110 to finish faster. The case we are optimizing is when there is dfu ongoing, just a simple boot.
Currently the main time...
Hi I have included Nordic Thingy52-SESFW to build my thingy:52 file and was at first met with path issues of nordic_common.h and core_cm4.h but have included them by adding...
Hello,
I integrated the nrf-ble-driver static library in a dynamic library that is going to be used in a Windows C# application (through a wrapper), as show the picture...
Anyone know where can I find the online power profiler for the nrf9160?
I was under the impression this was available, but I can't seem to find it anywhere.
hello nordic
i am working on a project with nrf52832
we need to be reading and writing to 2 different tags near the system
is there a Nordic hardware for such...
Hi. I'm trying to use command line tool, but an error occurred as shown in the picture below. Let me know why.
J-link was connected normally in segger embedded studio.
Hi All,
I need to implement security in Bluetooth. I have seen many threads but I could not get proper information regarding how can I implement or add security in a project...
Hi,
I am using the nRF52840 chip and supply iam giving from coin cell(3V). So i want to measure the coin cell voltage level monitor with nrf52840 ADC pin.
kindly provide...
Hi,
I was trying to program my sample to nRF5340's flash using nRF connect v3.4.1 and got this problem:
21:06:02.948
Application data folder: C:\Users\tuan.duong\AppData...
Hi everyone,
I was wondering if you have any advices or recommendations regarding the best type of debugging devices, or ways of debugging, for the nrf52840 Dongle, from...
I want to optimize my receiver power by putting the controller in sleep mode, that is ;-
NRF_POWER->SYSTEMOFF = 1;
And want to wake up the controller only when it receives...
When I try to increase the CENTRAL_LINK_COUNT from 8 to 9 in ble_app_multilink_central example, I got this error NRF_ERROR_CONN_COUNT . Is there a way to increase the max...
Hi,
I wrote a code using gps_controller.c on my thingy:91. However, i could never get a GPS FIX so i decide to try the GPS sample but it doesn't work neither.
I tried...
I'm using nRF52 DK to develop a BLE/UART application. My code is based off of the ble_app_uart peripheral example. In both my code and the default code, I get -0.1uA on the...
I am used NRF52810 controller, I wanted to know about there is possibility to work iic slave and iic master ( vice versa ) in single program ,can have any possibility about...
