I have been trying for a few days now to get my environment setup for development with the nRF51822. Since there is no official configuration for the Mac w/ Eclipse I have...
Apologies if this has been asked before but did search for 'format' in faq and got nothing.
I have been answering to questions.
In my answer I place hard empty lines....
Hi
i use nrf51822 s110 "hrs" example to transmit the data to ios.
I need to add an option to send back some data (from ios to nrf51822). 10 bytes maximum .
how can i implement...
Hi
i use the hrs example to transmit the data to ios.
but i need to add an option to send back data (from ios to nrf51822). 10 bytes maximum .
how can i implement...
Hello,when i get connected to the phone,when i call err_code = ble_hts_measurement_send(&m_hts, &simulated_meas) and err_code = ble_bas_battery_level_update(&m_bas, battery_level...
I got the Dynastream N5 kit and have successfully used it with limited ANT work and was trying to get BLE working but can't get a driver for the USB dongle. On the 51422 product...
Hi All,
I am working in the sleep mode with system off and wake up with internal RC clock.
It function well when connected to EV board...
I see the "Emulated System...
Hi,
I am working on a product based around an nRF52832 (SDK 15.3, S112 v6.1).
I am using the Secure Bootloader and I have a script that is used to merge hex files and...
Hi,
I'm trying to write multiple compile time constants into the UICR (from the boot loader project). Currently I'm writing the boot loader addresses (start address &...
I want to update NCP application in the field. NCP is attached as USB device on Raspberry pi which act as border router.
I am using open bootloader ( pca10059_usb ) and...
Hello.
We are currently developing PCB design of smartwatch with RF Nordic nRF24 chip, Johanson small ceramic antenna (P/N 2450AT42B100), and capacitive Touch Switch (AT42Q1012...
I am using asset_tracker as the basic program and basically it is running fine and sending data to the RF connect web page.
However approximately every 30 minutes I get...
I am looking for a simple example for I2C write. The TWI sensor example is not clear.
It would be great to have an example like the basic SPI example
i.e.
How to init...
Hi, My company is interested in doing bluetooth beacon location tracking of android devices for a VR project. I notice we can easily purchase bluetooth 5 beacons on amazon...
Hi,
I am trying to migrate my project file from Keil 5 to Segger Embedded Studio (SES).
After porting all my source code and configuration files, SES is able to compile...
Hello,
I want "nrfutil" CLI tool (To perform DFU OTA of BLE) for one of my device which is based on i.MX6ULL ARM based processor 32bit.
I found that using "pip install...
Hi,
I am using nrf52840 chip, there is Thread and iot coap library, and movement sensor. When sensor detect move, pin call interruption and send coap message.
Voltage...
Hi all, Within my application I've followed the example/fstorage to the letter however upon requesting a flash write to the s112 the nrf_fstorage_is_busy() function loops...
Hi,
I am working with nRF PCA10056 evaluation board and using SDK 15.2.0. I am using nRF52840 as a central scanner, where it will scan broadcast data from beacons.
I want...
Hello,
I'm having problems with resuming usbdevice from susspend state. I'm working on SDK 15.2 with SD140 (6.1.0). on custom board with nRF52840 IC rev. 2.
My application...
Hi, the power LED no longer turns on on my nRF52840 DK board. The board is still advertising when it is connected to a power source and I am able to connect to it with a mobile...
