Hello,
I found that there is a multiprotocol demo in folder Board\nrf6310\s110\experimental\ble_app_multiactivity_beacon,then I found it can implement concurrent connected...
Dear Sir
We got the problem on DFU upload firmware, it always failed in second DFU . We must unpair the device at iOS setting panel. Before next DFU.
Here is the log data...
Hi All,
My requirement is to read the data from nRF51822 device that is connected to a bluetooth and bluetooth is connected to a system using a .Net application.
I have...
Hi everyone,
I'm using the nRF51822 (pca10000 Dongle + pca10005).
My plan is to send one byte over the radio.
I tried to use the SDK-Example as a template but it's...
Hi,
Is that possible to run the radio_test_example (\nRF51 SDK_v5.2.0.39364\Nordic\nrf51822\Board\nrf6310\radio_test_example) on the nRF51822EK? If yes, what modifications...
we also produced self PWM for ADC wave form testing. when we stop transmission, we will get good waveform out, but when we starting transmission, output waveform shape is...
Dear Support,
I have some troubles with the Evaluation Kit for nRF51822 :
I use the broad as a central role with S120_nrf51822_1.0.0_softdevice.hex and example...
I have a custom board. It has its Tx and Rx combined into one wire bus. I am able to transmit data on the bus. But I am unable to receive any data on the board. This is because...
I have nrf9160dk. I want to give AT commands to the sdk through the processor instead of giving it from the PC i.e want to program the processor in a way so that we don't...
For testing direct advertising i used sdkv10 keyboard example, but when im disconnected device form nrf connect manually its resetting. I debug code found that in BLE_ADV_EVT_PEER_ADDR_REQUEST...
hello
I am a newbee in BLE dev.
I try to connect the sensor to the Adafruit board thrut BLE. The sensor is Sensor it is saw on nrf connect iOS as
I mod the HRM central...
Hi,
I am try to configure internal RC (LFCLK) but device hang in "sd_softdevice_enable(&clock_lf_cfg, app_error_fault_handler);" API.
Changed in "sdk_config.h" to enable...
Hi
When we enable the ADC on the nRF9160, we se a considerable rise in current consumption in standby mode, from sub-100 µA to several hundreds of µA (~400 µA). How do we...
Now that most or all of the Nordic nRF5 SDK is covered by the permissive 5-clause Nordic license (as of June 2017: https://devzone.nordicsemi.com/nordic/nordic-blog/b/blog...
Hi
we are working on ble_nus_c multilink implementation and had problems when more than 1 server is connected: we've noticed that data get mixed between servers.
when...
Hello,
I am using nRF52832, SDK_15.3.0, S132 SoftDevice and Segger for flashing the image.
Is there any sample code integrated with HDC2010 Temperature & Humidity...
Hello,
I use a debugger probe (Segger Jlink) with the sdk_config.h setting SEGGER_RTT_MODE_BLOCK_IF_FIFO_FULL.
When my probe is not connected, there my product is blocked...
Hi, I am new to Nordic BLE development and trying to create an application that has beacon functionality with firmware upgrade over the BLE with the mobile phone and Nordic...
Hi,
So I've been developing just fine on the latest V1.0.0 SDK and SES 4.18. I literally stopped and started a new debugging session and suddenly SES is trying to reflash...
Hello!
I have 3 NRF52840 Preview DK's with Q1AAAA revision ICs. I have been putting those to good use, but I want to test some stuff with SPIM at 32Mhz, which I understand...
Hi,
I am using nRF9160DK, nrf v0.4.0, zephyr v1.14.99-ncs1
I have been trying to measure the boot time from when I press the reset to when it gets to the start of the...
