Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I had a problem setting sniffer.
I use PCA10040e (nRF52810) V0.9.0.
I installed everything.
And copied file and folder to this path.
C:\Program Files\Wireshark\extcap...
Hi,
I am a beginner in ble and I am trying to understand the technology. I am trying to write to and read from FM24W256 FRAM through I2C. The reference I have considered...
Hi,
I checked " https://github.com/NordicPlayground/nrf5_clients_for_nrf91_network_service " firmware of nRF52 which works as client for nRF91.
But I can't find firmware...
Hi,
We have below questions regarding HFXO.
1.> Will softdevice or nordic HW be able to recognize that the 32 MHz crystal is non functional during run time (after the...
Hi,
I'm trying to flash the secure_bootloader example onto a nrf52840 DK, after generating a private key, flashing with SEGGER embedded studio worked, the device entered...
I have 2 questions, both related to power/current consumption.
My setup is a custom board, with mfw 1.1.0. I havev arlier seen current consumptions in the µA-range. I now...
Dear Nordic Support,
I am doing some test on the Thingy:91 v1.0.0 in Vietnam. I am running 2 examples: Asset Tracker with NB-IoT + GPS and GPS .
When I use the stanalone...
Hi,
How i can make the low power node to wake up until get acknowledgement . Please tell me how many ways we can try...In my project i used initiate_friendship() function...
It appears to me that the zb_zdo_ep_resp_t struct is missing a variable value attribute since the actual list of end points is missing. Should it not be similar to zb_zdo_match_desc_param_t...
Hallo All :-)
As an enthousiast hobbyist I've developed a custom board around an nRF52832-CIAA. When I started testing with a BLE secure bootloader from the SDK16 examples...
Hi,
I am currently working on " asset_tracke r" application. Actually, I need to read 128-bit UUID values of the BLE ibeacons present nearby the board (PCA10090) to be captured...
Hi, everyone!
We try to use THINGY:52 board for debug our MEMS lib from external sensor. But before use external sensor (i2c bus) i can't burn standard firmware that compiled...
Hi all,
I'm working with the reception of 802.15.4 packets on nRF52840 for which I have configure the radio as follows:
In the application loop we have:
...
