I have Nokia Lumia 630 and it works well with nRF51822-EK but only with SDK nrf51822_v5.1.0.36092 and SoftDevice 6.0.0. Now I decided to try DFU OTA. I programmed bootloader...
Hello,
I found that there is a multiprotocol demo in folder Board\nrf6310\s110\experimental\ble_app_multiactivity_beacon,then I found it can implement concurrent connected...
Dear Sir
We got the problem on DFU upload firmware, it always failed in second DFU . We must unpair the device at iOS setting panel. Before next DFU.
Here is the log data...
Hi All,
My requirement is to read the data from nRF51822 device that is connected to a bluetooth and bluetooth is connected to a system using a .Net application.
I have...
Hi everyone,
I'm using the nRF51822 (pca10000 Dongle + pca10005).
My plan is to send one byte over the radio.
I tried to use the SDK-Example as a template but it's...
Hi,
Is that possible to run the radio_test_example (\nRF51 SDK_v5.2.0.39364\Nordic\nrf51822\Board\nrf6310\radio_test_example) on the nRF51822EK? If yes, what modifications...
we also produced self PWM for ADC wave form testing. when we stop transmission, we will get good waveform out, but when we starting transmission, output waveform shape is...
Whenever I store my data in Flash using FDS (Flash Data Storage Library) it stores a random value (but fixed) even though I am giving it a value.
I run the same thing in...
Hi, As the title states when I try to add characteristic to my custom service the function returns error 16. I have set NRF_SDH_BLE_VS_UUID_COUNT and adjusted the linker accordingly...
Good day,
I am starting a new project where I am using the ANNA-B112 BLE device from ublox in a custom design. The ANNA-B112 interfaces with a host MCU over UART. I would...
Hi,
I have added nus service to the relay central and peripheral example.The relay board advertises and i can connect to the peripheral part of device through the nrf connect...
The mesh health model state is not restored following a reboot in the current version of the Mesh SDK using the light switch example.
According to the documentation, the...
Hello folks, I am new to Thingy 52 PCA 20020 model and I have downloaded nRF SDK 15.2 and I am using a Segger J-Link programmer/debugger. The thing is I would like to get...
In acces.h there is the publish period format definition, which is
/** * Model publish period structure. */ typedef struct { /** Step resolution. */ uint8_t step_res : ACCESS_PUBLISH_STEP_RES_BITS;...
Hello,
I was surprised that gcc did not optimized my strlen("FOO") construct (worse, in a code review, I argued that the compiler would do the optimization…)
It seems...
Hey there,
I am trying to develop with the Bluetooth Mesh SDK for NRF5.
We have two chips, NRF52840 and NRF52840/NRF52832and are using the light_switch example from the...
I need to save energy for my ble application. So I turned off the sensor when there was no ble connection. A ble connection is a condition for me to turn on the sensor, but...
How exactly are the UART pins selected for the nRF9160? I've searched and am unable to find a file to configure pins. I need to change to pins from the development board to...
Hi,
I'm working with the SAADC on an NRF52832. I'm using the SAADC driver from SDK15.2.
I have a problem with the calibration routine because it's generating DONE events...
Hello,
I am developing an application on the 52840 and so far find the SDK documentation quite confusing and somewhat contradictory. I need to write a simple TWI (I2c) master...
