Hi,
We are using the ble_app_uart example in evaluation board to read data from some sensors and send it to the nRF UART V2.0 in Android 4.4. Every 20 ms I am trying to...
I am try this at nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
Firt I connect to Android device and keep one whitelist.pp_addrs and one whitelist...
Hi,
Parameter uint8_t ble_gap_scan_params_t::filter is present in the documentation, but not implemented.
Checked for SDK 5.2.0 and 6.0.0.
devzone.nordicsemi.com...
After I get a Disconnected() event, I want to start scanning again, therefore try to call StartDeviceDiscovery() again.
IsDeviceDiscoveryOngoing was checked before.
The...
Hi, I wanted to ask a question regarding sending data.
I currently have external memory that will send out serial data (SPI) to the nordic microcontroller. I have saved...
Recently, I try to programme nRF51822 DK communicating with nRF2401e1 DK,unfortunately，which does not success. With setting radio configuration: TXPower,frequency channel...
E:\BLE\work\nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
SDK 6.0.0
Softdevice 7.0
When I connect to Android 4.4.3 device(Nexus7 II) will...
Dear Team
I use the Lwip_mqtt_publisher example from the SDK 15.3 with a PCA10056 board.
Also, I used an Ubuntu 18 Instance(IPv4, I used 6tunnel) to run the Mosquitto...
Hello sir ,
I have conneccted an BLE400 dev kit to an swc J-flash device. And i can't erase it.
Tried with nRFgo Studio on windows 10 an with linux nrf cmd line...
Hello,
I am using the chip nrf52840. I am trying to configure three pins (P0.09, P0.10 and P0.11) as output pins and I am trying to make set and reset functions for them...
Hi ,
I am using NRF52832 ,SDK15 my code is based on the HR_FreeRtos project , I am using the nrfx_wdt API to implement WDT in my code .
I am using a LDO for the voltage...
I'm developing a product that use the Nordic UART service over BLE and need something similar to a USB serial port, except with NUS. Is there a Windows 10 driver that works...
Dear Nordic Team,
Thanks for supporting.
Currently i am working in Mesh network. My application is Single Client control 100 Server Individually . Same like this https...
Dear Nordic Team,
Thanks for supporting.
I am new for mesh network concept. I want to control individual device in mesh network (May be more than 10 device). I have tested...
Hi,
I have a project that has a bootloader based on the SDK15.3 secure buttonless DFU example. During pre-production testing, the need for downgrading the app came up. So...
Hi,
I just wanna start off by saying I know there a lot of similar posts to this one here on the dev zone, but my problem with them is that none of them (from what I've...
Hello,
we're just planning to deplay our first border router for bigger in-house installations and wan't to use a USB-Dongle with the nRF52840 as NCP with the Openthread...
Hi All,
We are working on zigbee protocol and wants to replace the existing setup with nRF52840 . We have some below queries need your answers on the same to go ahead on...
Hi
I'm developing an application that is pretended to run on an nrf52810-based custom board, The code is a modification of the blinky example from the SDK 15.0.0, and for...
Hello,
on my previous project i rellay enjoyed the offline documentation of the sdk (SDK14.2).
Since we are using the Thread-SDK now, I haven't found a offline documentation...
