I will be deploying my nRF51822-powered devices into the field and the end user will not be able to have any physical access to, for example, power cycle the board. I need...
Hi,
We are using the ble_app_uart example in evaluation board to read data from some sensors and send it to the nRF UART V2.0 in Android 4.4. Every 20 ms I am trying to...
I am try this at nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
Firt I connect to Android device and keep one whitelist.pp_addrs and one whitelist...
Hi,
Parameter uint8_t ble_gap_scan_params_t::filter is present in the documentation, but not implemented.
Checked for SDK 5.2.0 and 6.0.0.
devzone.nordicsemi.com...
After I get a Disconnected() event, I want to start scanning again, therefore try to call StartDeviceDiscovery() again.
IsDeviceDiscoveryOngoing was checked before.
The...
Hi, I wanted to ask a question regarding sending data.
I currently have external memory that will send out serial data (SPI) to the nordic microcontroller. I have saved...
Recently, I try to programme nRF51822 DK communicating with nRF2401e1 DK,unfortunately，which does not success. With setting radio configuration: TXPower,frequency channel...
Hello,
i am finding that after i call app_timer_cnt_get() there is a constant power drain.
I have an Ultrasonic sensor. the ECHO pin will fire 2 times into a GPIOTE...
hi.........
how to add the timer mode in hts program , i want to set the timer in my program to receive the data according to timing .
i am using segger 15.2 version ...
When I power the 52840 from a LiPo connected to VDDH and using VDD/VEXT to power 3V3 components, when the chip is put to sleep is the output on VEXT switched off? Or do I...
Hello, above is the PWM modulation waveform (positive Xuan Bo).
How does 1.nrf52832 regulate the frequency of circulation?
Take this nRF5_SDK_12.2.0_f012efa\examples\peripheral...
Hello, I want to use nrf52832 to output waveforms as shown above.
Using the Demo1 example in D: Lianxi nordic nRF5_SDK_12.2.0_f012efa examples peripheral pwm_driver, we...
I am sending 6 packets of 20B each data using ble_nus_string_send() function at every 120ms using app timer. but the function returns error BLE_ERROR_NO_TX_PACKETS. So unable...
From the latest Nordic SDK 15.2, I'm running the usbd_cdc_acm example on an NRF52840 connected to a PC using USB. The firmware correctly executes the USBD_POWER_DETECTION...
Hi,
I develop on nRF52 with linux/eclipse but to debug, I would like to use the sniffer. This one is only available on windows then I try to install it on a Windows 7 64bits...
I have successfully implemented Scanning and Advertising at the time using s132 on nrf52832 with SDK14, it works very stable and fast which satisfied me.
Recently, I was...
Hello,
I've been using the SDK 15's "ble_app_uart" example and I've been curious on how the function nus_data_handler() gets called after data is sent over BLE. More specifically...
hello,
I am newer to nrf. I am using nrf52832 development kit and using soft device 5.0.
I have confusion with two function with nrf_log_info and printf?
which should...
Hi,
I want to know if we can send Mobile Notifications or send sms to nRF52832. i want to do some operation based on notification or sms received from sms on mobile..
Hi,
I am currently trying to setup my sdk 15 on my pca10040. I already have a working I2C source for a BME280 and it works fine using the SDK 12 (pca10040), I get the current...
