How do you create hid information for a joystick and send it over BLE. Nordic doesn't seem to have
primitives for this (they have keyboard and mouse facilities). I'm working...
I use a PCA10001 board as peripheral role of heart rate service and it can be discovered by control panel. But as I download the experimental program of central role of hrs...
I'm reading the source for the nRF Toolbox app for Android 4.3 and comparing it to the Proximity Profile spec from the Bluetooth SIG, which has this to say about path loss...
Hello,
I have downloaded the software related with the "nRF51822 Bluetooth Smart Beacon Kit" in order to modify typical iBeacon's parametres such as UUID, Major ID, Minor...
Hello,
i would like to know if the new SoftDevice 130 for the nrf51822 is compatible with the DFU OTA bootloader example provided in the SDK (nrf51822/Board/nrf6310/device_firmware_updates...
Hi Community,
I'm a little bit flyiing in the dark, so I like to ask this in the devzone.
Does anyone already implement NFC OOB Pairing and using Apple GymKit?
1...
We are not using the USB interface on the nRF5340, and thus are leaving VBUS and DECUSB unconnected. Can we also leave D+ and D- unconnected?
Thanks,
Scott
To the kind attention of Nordic support team,
I'm interested in understanding in a conceptual way, how the microcontroller is operating when sd_app_evt_wait is called. ...
We have the following setup: - Both nRF52832 and nRF52840 chips in our product
- The nRF52832 is a module while the nRF52840 is the chip integrated directly onto our PCB...
Hi,
Kit:nrf5340
SDK:nrf connect SDK 1.5.0
1.Can you please explain how the data transfer takes place in ble mesh while using nrf connect SDK.
2. Also tell me how...
The servo I use in my application uses a PWM signal duty cycle to represent servo amperage level.
So, to measure servo amperage, I use a GPIOTE channel to capture the time...
Hi!
I'm using ncs v1.5.0 and mfw 1.3.0 on a nRF9160 DK v0.15.0.
I'm using gps sample with supl_clint_library enabled
1. Things work reasonably well, but I am confused...
I'm trying to write a driver for an SPI peripheral.
west says:
```
../ncs/zephyr/samples/sensor/mydriver/prj.conf:5: warning: attempt to assign the value 'y' to the...
new uses SDK 17.0.2, SD 7.2.0
old target used SDK 15.2.0 and SD 6.1.1
Attempting to update BL, SD, and App over DFU.
1. If merging all new BL settings with SD, BL, and...
Hi,
I am using nrf connect SDK and compiling nrf5340 examples.
I want to implement a security related example in nrf connect SDK.
Can you please tell me
1. Security...
Hi,
I am trying to open serial lte modem app to evaluate power profile on thingy91. i am using toolchain manager (v1.4.99-dev1) to open Segger Embedded Studio.
While building...
This compiles with warnings and the value always comes back as 0
#define SW1_NODE DT_ALIAS(sw1) #if DT_NODE_HAS_STATUS(SW1_NODE, okay) #define SW1 DT_GPIO_LABEL(SW1_NODE...
Hello,
I have a application on a nRF52840DK as central. The code is based on the ble_app_uart_c example.
I need to send a lot of data through UART into the serial port...
I have followed various advice to create an SPI/I2C driver an own-designed device using the bme_280 example as a model
As this could be either SPI or I2C I put both configurations...
Hi all,
I am currently working on a project which uses the ble_app_uart_c example. I have a nRF52840DK as central. The central receives NUS pakets with a average data rate...
