I will be deploying my nRF51822-powered devices into the field and the end user will not be able to have any physical access to, for example, power cycle the board. I need...
Hi,
We are using the ble_app_uart example in evaluation board to read data from some sensors and send it to the nRF UART V2.0 in Android 4.4. Every 20 ms I am trying to...
I am try this at nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
Firt I connect to Android device and keep one whitelist.pp_addrs and one whitelist...
Hi,
Parameter uint8_t ble_gap_scan_params_t::filter is present in the documentation, but not implemented.
Checked for SDK 5.2.0 and 6.0.0.
devzone.nordicsemi.com...
After I get a Disconnected() event, I want to start scanning again, therefore try to call StartDeviceDiscovery() again.
IsDeviceDiscoveryOngoing was checked before.
The...
Hi, I wanted to ask a question regarding sending data.
I currently have external memory that will send out serial data (SPI) to the nordic microcontroller. I have saved...
Hi,
I have a problem in my application, i want to add scanning feature, but
When i call sd_ble_gap_scan_start () with these parameters it returns error (0x06) (with...
I am a begineer in Nordic trying to read voltage and current readings from ADC pin. I need to read both values in parallel, with known interval. So I need to use interrupts...
I am trying to use the LTE Sensor Gateway app to send Running Speed and Cadence Service Sample Application data loaded on a nRF52832. I have managed to get this two device...
Hi,
I have a problem with timer and nrfx. I use the migration guide:
So I r emove the old configuration entries related to the nrf_drv_* drivers from my sdk_config.h...
Hello,
I am currently using nRF52832 with SDK v11.0.0 and S132 v2.0.0. I am also using the soft device as my application requires. I have been trying to put the CPU into...
Hello, When i try to use nrf9160 with the BME280 sensor over I2C i get this error
***** USAGE FAULT ***** Illegal use of the EPSR ***** Hardware exception ***** Current...
Hello,
I am using BLE+MCU MBN52832 module and i am facing one issue while programming my application.
I am uploading the hex file using nrfGo Studio and when i try...
I have a custom nRF52840 board that I am implementing the Open Bootloader (from SDK 15.3). Push Button/Power control is handled by the STM6601 device. It keeps the power ON...
When I open a new project in SES and paste the code of blinky led example from " \nRF5_SDK_15.3.0_59ac345\examples\peripheral\blinky\pca10040\s132\ses ", and start compiling...
Hi. every one
First of all, i am a beginner.
I connected the max44009 and CJMCU2080 sensors to the board.
and also get a value.
but sgp30 sensor is faile
there...
HI. i use SEGGER Studio and SDK 15.3.0.
I usally use printf func for debug. however as use SDK func, I need to use NRF_LOG_INFO casue SDK file use NRF_LOG_INFO for debuing...
Hi,
I am trying to port an existing project to a Mesh SDK example. Some files include the math.h library and use the round function. During the build process I am getting...
Hi I use nrf-ble-driver ver.4.1.1 with PCA10031 dongle (nRF51844 chip on board) and "connectivity_4.1.1_1m_with_s130_2.0.1.hex" firmware for that dongle. in this case ATT_MTU...
Hello to everyone. I´m starting to work with Mesh configuration in nRF52 SDK. I was testing the "light_switch" example as client and server in Mesh v3.10, provisioning with...
