Hi,
Is that possible to run the radio_test_example (\nRF51 SDK_v5.2.0.39364\Nordic\nrf51822\Board\nrf6310\radio_test_example) on the nRF51822EK? If yes, what modifications...
we also produced self PWM for ADC wave form testing. when we stop transmission, we will get good waveform out, but when we starting transmission, output waveform shape is...
Dear Support,
I have some troubles with the Evaluation Kit for nRF51822 :
I use the broad as a central role with S120_nrf51822_1.0.0_softdevice.hex and example...
Suppose a nRF9E5 transmitter is set for continuous transmission on a channel.
A nRF9E5 receiver listening on that channel:
finds carrier and sets CD
finds address...
I will be deploying my nRF51822-powered devices into the field and the end user will not be able to have any physical access to, for example, power cycle the board. I need...
Hi,
We are using the ble_app_uart example in evaluation board to read data from some sensors and send it to the nRF UART V2.0 in Android 4.4. Every 20 ms I am trying to...
Is it OK to drive GPIO P0_27 (when configured as an input, of course) above the supply voltage provided the input current is limited with a series resistor?
In my application...
I'm attempting to build a binding for the noble ( https://github.com/noble/noble) BLE library. Currently some methods are private by underscore prefix convention.
I'd like...
I used nrf52832 sdk14.2 development, modified on the basis of the ble_app_template project, and ported some of the user code previously in sdk12.3 to sdk14.2. After I open...
Hi,
I want to store some data into flash and need to read before calling gap_params_init() in proxy_server demo.
1) when I am initializing flash manager using flash_manager_init...
Hi I wanted to flash a firmware in a Thingy52, I used Segger embedded studio and NRF52 DK to do that. I used the right cable but after flashing my Thingy52, it doesn't blink...
Hello dev zone !
I shall design a compact hardware solution wich is cost sensitive.
I need to use a NRF52832QFAA, I need to provide a 16mhz clock to a hardware peripheral...
I want to implement the function of long Attribute Value reading and writing in BLEV4.0. How should nrf52832 sdk14.2 implement this function? Is there a routine for reference...
I am trying to create a beacon application based on nrf52810.
I am using the following…
* SDK: 15.2.0
* IDE: Segger Embedded Studio
* Hardware: PCA10040 V1.1.1
...
hi.... i am working on ble_uart in segger ... while i am debugging my program stop at nrf_breakpoint_cond ...
how to enable the logging ... please have a look at pic......
hi...
i merged the ble_uart and twi sensor program in segger 15.2 using nrf52832
i have flashed the program successfully, i am getting fatal error while i am debugging...
Hi Sir
We'd want to make lot of nrf52840 devices, and all devices included open bootloader program,
however, the each device USB SDFU port number are different (COM30...
Hi,
I am usig nRF5_SDK_15.0.0_a53641 and writing a program with keil .
I am tryng to read data from the acceleration sensor( LSM303DLHC ) bu communication with BLENanov2...
Hello All,
Confirm the chip set replacement for the NRF51822 with NRF51802?
Can anyone suggest me which one is better with reference technical features.
Thanks
I used nrf52832 sdk14.2 development, modified on the basis of the ble_app_template project, and ported some of the user code previously in sdk12.3 to sdk14.2. After I open...
