Dear Sir
We got the problem on DFU upload firmware, it always failed in second DFU . We must unpair the device at iOS setting panel. Before next DFU.
Here is the log data...
Hi All,
My requirement is to read the data from nRF51822 device that is connected to a bluetooth and bluetooth is connected to a system using a .Net application.
I have...
Hi everyone,
I'm using the nRF51822 (pca10000 Dongle + pca10005).
My plan is to send one byte over the radio.
I tried to use the SDK-Example as a template but it's...
Hi,
Is that possible to run the radio_test_example (\nRF51 SDK_v5.2.0.39364\Nordic\nrf51822\Board\nrf6310\radio_test_example) on the nRF51822EK? If yes, what modifications...
we also produced self PWM for ADC wave form testing. when we stop transmission, we will get good waveform out, but when we starting transmission, output waveform shape is...
Dear Support,
I have some troubles with the Evaluation Kit for nRF51822 :
I use the broad as a central role with S120_nrf51822_1.0.0_softdevice.hex and example...
Suppose a nRF9E5 transmitter is set for continuous transmission on a channel.
A nRF9E5 receiver listening on that channel:
finds carrier and sets CD
finds address...
Hi,
Can the value of NRF_RTC1->COUNTER be read safely from the main loop without first stopping the RTC or temporarily disabling the RTC1 interrupt etc? (nRF51822 or nRF51922...
I used the nRF51822 Evaluation kit and flashed the BLE_proximity example on to the PCA100001 board.
In the master control panel the USB dongle measured -46 dBm(Nordic_prox...
Hi all,
what if I want a sensor network in my house with BLE. Can I just install, for example, 16 nodes in my house and connect to all of them with one iPhone? Or would...
Hello,
I am currently using nRF24L01P with TI CC2591 in my RF module product.
I have a doubt that need your help to clarify.
Does the antenna impedance given in the...
We've been trying to user the AES hardware module in ECB mode.
To do that we used the sd_ecb_block_encrypt function.
Is this hardware accelerated? Based on power consumption...
Hello,
I would like to know if I could interface the nRF51822 with an Arduino Mega Board. Could you give me some advices to do that?
Thanks for your help
Hi,
i need to use a watchdog in my application. I read that i can use the build in one, but i thing my configuration or the usage of the watchdog is wrong.
here is my config...
Hi guys,
I am getting started with your nRF51822 dev Kit. I got the nRFGo Starter Kit (nRF6310 Rev 1.4 mother board) as well. Most of the examples work as expected. But...
Hello,
I'm trying to do a millisecond counter using app_timer but the callback is never called. I think I have missunderstood how it works.
I've tried using the app_timer...
Hi,
Im trying to send 20 packages of 30bytes each as fast as possible, so I created the following loop:
for( pack=0; pack<20; pack++)
{
w_tx_payload_noack(30, MegaBuffer...
Hi all,
I have a custom board with the Nrf51822 BLE chip and it works in broadcasting mode without connection only. Basically it sends the advertising data on an established...
Hi
I have some problems about using your Master Emulator API. I want to write a dynamic link library with C++, but I don’t know how to invoke the MasterEmulator.dll.
The...
I'd like to use LPCOMP. I'd like to get rid of the 12K pulldown on SWDIO.
I can tell from PCN-082 that QFAA CA and C0, as well as QFAB AA and A0, will let me do that. ...
