we also produced self PWM for ADC wave form testing. when we stop transmission, we will get good waveform out, but when we starting transmission, output waveform shape is...
Dear Support,
I have some troubles with the Evaluation Kit for nRF51822 :
I use the broad as a central role with S120_nrf51822_1.0.0_softdevice.hex and example...
Suppose a nRF9E5 transmitter is set for continuous transmission on a channel.
A nRF9E5 receiver listening on that channel:
finds carrier and sets CD
finds address...
I will be deploying my nRF51822-powered devices into the field and the end user will not be able to have any physical access to, for example, power cycle the board. I need...
Hi,
We are using the ble_app_uart example in evaluation board to read data from some sensors and send it to the nRF UART V2.0 in Android 4.4. Every 20 ms I am trying to...
I am try this at nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
Firt I connect to Android device and keep one whitelist.pp_addrs and one whitelist...
SDK15.3
nRF52840
S140 v6.1.1
Q1. I have an RTC compare event connected to a Timer count task over PPI. The Timer is configured in low power counter mode. My question...
Hi, I am strugling to get the power comsumption down to the number I have been reading on this forum. I followed the instruction of the dev kit manual . When measuring the...
Hi, I'm getting regular crashes with my app: SOFTDEVICE: ASSERTION FAILED. Using and NRF52832, SDK 15.3.0, SD 132 6.1.1, and Mesh SDK 3.1.0. With DEBUG defined, I don't really...
I'm trying to interface 2 SPH0645 mics to the nRF52840 DK.
Little did I know when I bought them (the mics) that you need to waste 2 timers + 2 pins + memory space to make...
Hi,
I am trying to measure a signal using the SAADC driver on SDK 13. I have used the example from the nrf52 playground for low power ADC
I have a few questions on best...
Hi,
I have a nRF91 development kit and want to connect P4 to the Segger Jtrace for ETM streaming. In the manual, it stated that a 2×10 pin 1.27 mm pitch surface mount connector...
Hi,
Is there any way to get network time without previously setting it with AT+CCLK?
I would like to implement sort of "fake time" by initialising it with the network...
Hi, I'm struggeling with this stage on the "getting started assistant"
"Clone the nRF Connect SDK"
Is there any step by step video to help me do this, I have probably...
I have one service with multiple characteristics(11). Out of 11 characteristics I have 7 characteristics which have notify as their attributes. So when I select the notification...
I have been using nRF9160: LTE Sensor Gateway to send data from nRF52832 to the cloud. The nRF9160 is subscribed to nRF52832 and hence gets updates after every certain period...
Hi,
I'm trying to use Power Profiler Kit (PPK) with nRF52 DK to measure the power consumption of our custom hardware. My setup is as described below: - The PPK is connected...
SDK:15.2
IC:NRF52840
Hi，When I upgraded the device using usb dfu, after entering the app, there will be an additional current of about 180uA（Sometimes appear）.
Both...
Somehow my nRF9160 DK board has become essentially unresponsive. Flashing new modem using nRF Connect Programmer, and downloaded nRF FW, "seem" to work. But nothing else....
The asset_tracker repo now has a file called: prj_nrf9160_pca20035ns.conf
Is this still compatible with the nRF9160 DK that is using pca10090n ?
What does the pcsNNNNNn...
Hello everyone,
im using the nRF52840 DK, softdevice s140 and the ble_app_tamplate example. In this example i can send data through the GATT protocol. But i want to change...
