Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
I am developing an android app which is connecting with this product. In that particular case my app advertises, the nRF scans and initiates connection with my app. Some phones...
Hi Nordics,
we would like our central nRF52840 to have DFU timeout in 20 seconds , if no connection received via nRFconnect phoneAPP to perform the firmware udpate, then...
Hi Team,
I have a some query regarding nordic mesh
I would like to know that Nordic mesh is compatible with CSR mesh ?
Does nordic mesh is compatible with any 3rd...
Dear: Addressee
Hello!
I have a question about the program development of Bluetooth chip.
There is no client program for blood pressure measurement in SDK (15.2.0...
To do a serial DFU I have followed the steps provided in the DFUMaster_UART link.
1) Generated the key using the NrfUtil.
2) Added the private.key and generated a DFU...
Hi,
I try to flash application + softdevice + bootloader into the nrf52810 with following commands but it does not work? Can you look into this?
nrfjprog --program...
Hi,
We are developing central scanning mode for our project requirement. We want to scan BLE tags which are transmitting at every 10 seconds. I have been using nRF52833...
Hello, I have a working application that transmits data to a smartphone using NUS, based off of the uart example. I would now like to integrate bonding into my application...
I have an NRF52 DK and a J-Link mini debugger. I'm trying to connect J-Link debugger to the NRF52 via the debug jumper port. I'm using a standard 10 pin SWD JTAG cable. I...
i m working with fds using segger, i'm trying to perform read and write functions and printing on putty. it showing no errors on building while debuging no output is displaying...
When create 128byte length's CHARACTERISTIC and read with NRFCONNECT on Android. NRFCONNECT returns GATT_READ_NOT_PERMIT even though sd_ble_gatts_rw_authorize_reply() completes...
Hello Team Nordic,
I have a strange problem with the UART:
I am using nRF52840 with two UARTs: UART1 for Debug-Terminal and UART0 for communication with a GPS-Module...
I have developed a code for transferring data through uart to ble. It is working properly. but when I add a line printf to my code the data transmission stops and ble will...
Hello, I am trying to use the Legacy TWI Driver in SDK 15. I have setup my my sdk_config.h file to remove all references to NRFX (New TWI Driver). Only enabling the "nrf_drv_twi...
Hi!
I have download nRF5_SDK_14.1.0, and I have IAR Embedded Workbench IDE ARM 8.20.1
I want compile ble_app_eddystone.eww from examples, but have error:
Error[Lt009...
