Hello,
I have downloaded the software related with the "nRF51822 Bluetooth Smart Beacon Kit" in order to modify typical iBeacon's parametres such as UUID, Major ID, Minor...
Hello,
i would like to know if the new SoftDevice 130 for the nrf51822 is compatible with the DFU OTA bootloader example provided in the SDK (nrf51822/Board/nrf6310/device_firmware_updates...
Can I get uuid of central device from peripheral device(nrf51822) ?
I want to check out which smart device is connected.
May be I can tell central is iphone4s or iphone5...
Recently s110_nrf51822_7.0.0 softdevice has been released. I cannot find specification where those new amazing features (they are impressive, indeed :) ) are described, so...
Hi All,
Please correct the following in my understanding. Also , i am planning to build a
remote controlled device using a PWM output. How does ATT,GATT and GAP affect/influence...
Hi,
I'm trying to deal with long write events (37 bytes long) but on adding a second long write characteristic I'm facing the NRF_ERROR_NO_MEM error on adding it.
The...
Hi Sir,
Since Zigbee_Thread 3.2 released, we prepared two 52840-DKs for consumption test.
One is the door lock example (device #1 Thread_Zigbee_3.2.0\examples\multiprotocol...
I notice that the question has been asked as far back as 3 years without any answer!
There are several parts of the datasheet that mentions internal reference voltage sources...
Good morning Mrs
I have a bluetooth module SKB501 which integrate a NRF52840 chip. In that NRF52840, i want to test a code (ble_app_uart) include in the "nRF5_SDK_15.3.0_59ac345...
Hi. We are using RTC2 in our application to trigger an event at 256Hz. We also have a compare running to trigger a compare event at 32Hz.
I have found that over an hour...
Hello guys,
I am using nRF52840 and SDK 15.3.0. Trying to use SPIM3 device because of the speed.
In my sdk_config.h file, I set both NRFX_SPIM_ENABLED and NRFX_SPIM3_ENABLED...
SDK: 15.3.0 Example: ble_app_multirole_lesc Device: EYSHJNZWZ (nRF52832)
I want "nRESET" to be set without pull-up. How can I use "nRESET" without pull-up?
Hello,
While importing the needed libraries for a project I stumbled upon an error in the app_error_handler_gcc.c and app_error_handler_iar.c files. The error is
nrflibraries...
I am using a SPI peripheral on the nRF52832. If the SPI bus is busy when I call
err_code = ble_advertising_start(&m_advertising, BLE_ADV_MODE_FAST);
the routine returns...
Hi, I'm working on a simple SAADC acquire in scan mode.
I create the two following function:
I was able to init and read the adc without problem.
If I remove the...
Hi All, I'm doing some investigative around existing mesh models. In the Mesh Model Bluetooth Specification, Section 7.1, we have a specification, for example:
Generic OnOff...
Hi,
I am considering now the timings during a BLE connection, especially for long range. For that I came across the range delay given in the latest BT Link Layer Specification...
Dear nordic,
I have application that developed using development kit pca10040 . I want to change it to supporting nRF52810. i follow the instruction the link :-
http:...
Hello,
I am developing a solution that measures values on 2 AIN channels in scan mode with the following setup:
- differential mode
- no oversampling
- no burst mode...
%XMONITOR seems to report <reg_status> set to 1 or 5 even though the device has lost connection to the base station - for instance by being moved out of range. Mobility is...
