I will be deploying my nRF51822-powered devices into the field and the end user will not be able to have any physical access to, for example, power cycle the board. I need...
Hi,
We are using the ble_app_uart example in evaluation board to read data from some sensors and send it to the nRF UART V2.0 in Android 4.4. Every 20 ms I am trying to...
I am try this at nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
Firt I connect to Android device and keep one whitelist.pp_addrs and one whitelist...
Hi,
Parameter uint8_t ble_gap_scan_params_t::filter is present in the documentation, but not implemented.
Checked for SDK 5.2.0 and 6.0.0.
devzone.nordicsemi.com...
After I get a Disconnected() event, I want to start scanning again, therefore try to call StartDeviceDiscovery() again.
IsDeviceDiscoveryOngoing was checked before.
The...
Hi, I wanted to ask a question regarding sending data.
I currently have external memory that will send out serial data (SPI) to the nordic microcontroller. I have saved...
Recently, I try to programme nRF51822 DK communicating with nRF2401e1 DK,unfortunately，which does not success. With setting radio configuration: TXPower,frequency channel...
Hello,
We have multiple NRF52840 dongles that we want to repurpose as receivers for the NRF Sniffer software. Browsing throughout the forum we've came to the conclusion...
Hi,
I need to create a dynamic array to send a different number of bytes of data using TWI. Here is how I create an array:
When using the malloc function, I always get...
Hi
There was a problem using the external ADC AD7792 in a project with SoftDevice. The problem is that when the ADC is processed in a project with SoftDevice, the waiting...
We have implemented proprietary audio streaming on the nRF52. It reads Audio from a PDM mic and uses the timeslot feature of the BLE radio to send said audio to another BLE...
Hi:
I already updated the SDK to the first release version V1.0.0 and the unit works well with NB-IoT, UART and SPI. I'd like now to include real GPS data but I can't get...
Hello, I'm working on programming a cycle to measure the power consumption. I need to send a message and wait for a response for some time, then shut the modem off, no matter...
Hi,
We were planning to use a spectrum analyser in order to do the radio test on the nrf52-dk. Where should the analyzer be connected? Should it be connected to the J1...
Hello, I'm trying to test the UART example for nRF 9160 DK. To my understanding, any input sent through one of the ports should appear in the other one (from uart1 to uart0...
I would like to use PSM to save power consumption of nRF9160 LTE module. However, if I use PSM on the module, the module is dormant and not able to receive the command from...
Hi, this might be a trivial question but I'm struggling to find the solution. I want to configure the asset tracker application so that it works with real GPS data on the...
hello!
i am using my nrf52832 with s132 softdevice. basically the ble template with my services and charas.
i checked power consumption in sleep mode and observed something...
Adding a Network Coding Extension to CoAP for Large Resource Transfer
https://ieeexplore.ieee.org/document/7796871
Can I use this coding in your some SDK project?
...
Hi all,
I ned to test DTM in labview. In nRFgo Studio works fine, but I don't have any idea hoe to relize same test in labview. Could anyone help me please?
Thank you...
Hi,
I'm working on nrf9160 DK board version 0.8.5. I want to use analog pressure sensor and read data using GPIO input, however there is a little issue related to acceptable...
