Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Hi,
i tried to send data from ios 7 via tx_characteristics(like in UART example) but received error:
didWriteValueForCharacteristic 2A38 error = Error Domain=CBErrorDomain...
I have been trying for a few days now to get my environment setup for development with the nRF51822. Since there is no official configuration for the Mac w/ Eclipse I have...
Hai ,
I need to update nrf52840 over ble from esp32 . first i tried with app , firmware gets updated .. as per the dfu protocol i understood flow and tried to writing data...
I need atleast 10 UART channels to be configured in my project. Is it possible to do it with the NRF52840. I believe because of the PPI I should be able to do this. I was...
I want to create a small bluetooth device with the nrf52823 chip. I want to use a lithium battery cell to power the whole circuit and therefore it neet to be low power. On...
I'm bigger of NRF52832 and beacon concept. I need modify my beacon data like Major,minor and Tx power change via mobile app configurable. please share any example code or...
I purchased a new nRF9160DK. Upgraded to latest 1.1.0 firmware. I built the AT application and can talk to the modem using the LTE Link Monitor application.
The DK came...
Hi, I'm working on nRF52832 at SDK ver15.3.
My problem is Current consumption increasing (82uA -> 550uA) when WDT Reloading in sleep mode.
I set WDT configuration "Pause...
I am trying to send and receive a response from a machine using Modbus (TTL to Rs485) and nrf51822.
Connections: R0 -> RX(P0.11) ,D1->TX(p0.09), RE&DE->P0.19,VCC->5V
Just...
Hey
We have successfully put the dongle into operation. We were able to develop and successfully test our software.
As soon as we test it with the JLINK on the module...
Hi
I have problem because i dont get all data which are in FIFO uart on my smartphone via BLE. Nrf as i can see in example sends data where data[index-1] == 0x0d || d ata...
I'm working with nRF52832 and playing around with some peripheral examples from SDK 16.0.
The FreeRTOS based heart rate sensor example ( ble_app_hrs_freertos) seems to work...
Hi.
We are using the Nordic UART service. Our project is based on the example project "ble_app_uart" from version 15.2 of the SDK. I've found after about 3 minutes it stops...
So I have been saving a structure using FDS and it seems to be working fine but after a while (2-3 hours of updating value every 10 seconds) the fds_record_update(); function...
CONFIG_MAIN_THREAD_PRIORITY=7
I read prj.conf of mqtt_simple. Why is the value of 7 given?
https://github.com/NordicPlayground/fw-nrfconnect-nrf/blob/master/samples/nrf9160...
Hello,
I am having issues detecting my board with some phones. I have tested it with a Samsung Galaxy S8+, Android 9, and with android 5.1.1. However, I can't detect it...
