Based on the nRFUart demo, I added a masterEmulator.DiscoverServices() block before the DiscoverPipes() block in a very similar manner. Purposed is to be able to get more...
Hi,
There is much talking about the "large data transfer" over BLE, the l2cap channel being the best option for the moment.
However, does anyone know the datarate achievable...
NRF24AP2 with MSp430F149 . ASYNC 9600 N 8 1
step 1 : reset NRF24AP2 with reset pin , and received a pulsing signal through RTS pin
step 2: send a char (0x4A) to NRF24AP2...
Hi guys,
I am using the gcc setup to program my boards. However for flashing the softdevice I use nrfgoStudio. SO I downloaded the hex file and fashed the siftdevice. But...
How do you create hid information for a joystick and send it over BLE. Nordic doesn't seem to have
primitives for this (they have keyboard and mouse facilities). I'm working...
I use a PCA10001 board as peripheral role of heart rate service and it can be discovered by control panel. But as I download the experimental program of central role of hrs...
Hello All
Currently i am using nRF51422-DK (PCA10028) Board .I am planing make mesh network using nRF51 devices.i go through the mesh network introduction document which...
Hi,
I'm trying to set a button as an interrupt source. I wrote this code:
void Init(void){
pwrmng_MainStatus = PWRMNG_STS_STARTUP;
//LED
#ifdef DEBUG_LED
nrf_gpio_cfg_output...
I want to read the status of LFCLK,but I find that ,the value I have readed is awayls zero! my code is follow :
LFCLK_State = ((NRF_CLOCK->LFCLKSTAT) >> 16) & 0x00000001;...
Hi,
I had done secure OTA in nRF51 DK board using SDK 12.2.0 and s130 2.0.1 softdevice. Now, i am trying to same thing with my custom Board RL-51822-A1.
For that first...
I cloned the demo project inside the Keil MDK5, from the following path:
pack installer
device = "nRF51822_xxAC"
examples = "uart_pca10028, UART_Example_Application...
Hi,
I want to use the nRF BLE Sniffer to detect wether a connection (between my fitness tracker and smart phone) is present or not.
I am able to get the advertisement...
hi,
I am struggling to create custom service to send the simple message to the client device where both devices are nRF52832 (Server and client). when I receive the message...
I have 2 of the nRF51 Dev. kits and have been ble to run Blinky, BLE_UART and set up the 2 dev kits so that I can send data from one DK to the other and to an external board...
Hi,
I tried to flash the mbed FOTA bootloader on my nrf51 DK. I copied the bin file to the bootloader device. It said the storage on the device is to small. Now it won...
1- I am looking for Bluetooth Chip to control a DC Motor.
2- This Chip need to be small since it will be fitted on a small narrow PCB (10mm width x 110mm long PCB).
3- Chip...
Hi guys,
I want to ask if it is possible for a nrf51822 to connect to a Central ( my cell phone) without advertising. Let assume that my cell phone has nrf51822's MAC address...
Hi,
I am using st-link debugger with NRF51822 module.
I was trying to connect it openocd, but it failed. st-link is working with STM32 processor and able to flash through...
Hi,
I found a suspicious line of code.
SDK: nRF5 SDK 13.1.0 (7ca7556)
File: peer_data_storage.c
Function: pds_peer_data_read
At line number: 415
if ((*p_buf_len...
Hi,
I made a custom board with nrf51822 and custom antenna which works fine for examples which use SDK10 + SD110.
For my application it was recommended to use SDK12.3...
