Hi,
I use UART bootloader SDK example(dfu_dual_bank_hci) to do update firmware on EK PCA10001 board,it can work ok.But i changed the HCI_SLIP_UART_RX_PIN_NUMBER and HCI_SLIP_UART_TX_PIN_NUMBER...
Hi. I have been trying get a notification through ANCS.
I have created an app which is made by modifying ble_app_ancs sample.
It works basically but there is one problem...
Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
To be able to upgrade FW through UART, a bootloader for nrf51822 is required in my project. I have tried out the example bootloader in SDK. But this example is using softdevice...
I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
nRF5_SDK_17.1.0\nRF5_SDK_17.1.0_ddde560\examples\peripheral\blinky_freertos
nRF5_SDK_17.1.0\nRF5_SDK_17.1.0_ddde560\examples\peripheral\blinky_rtc_freertos
I burned these...
I am using nRF52840 to interface my MPU6050 sensor via I2C , I build and flashed the program and there were no problem. But I can't see any clock signal on the default I2C...
I'm trying to build the zephyr/samples/net/sockets/http_client. I selected thingy91_nrf9160_ns for the board config and it builds and works fine. However when I enable
...
In my project, need an external sram with SPI interface to increase the sram volume.
I'm not sure if I can do it，please give an exsample in C language and some tips.
An...
Some of the products we produce do not work after about 10 days. Our firmware starts the watchdog module as soon as it starts, and sets the timeout period to 30s. And read...
I would like to implement ANALOG Modulation schemas on nrf52 serias family (e.g. AM, FM, SSB)
Do I have a direct access to IQ samples OR basic properties of the radio carrier...
I am using is25lp03d flash with "nordic,qspi-nor" driver.
The issue is that nrf_qspi_nor.c driver uses `nrfx_qspi_mem_busy_check()` before entering suspend mode. This function...
The %XCONNSTAT read command returns the total amount of data received/transmitted "in kilobytes". By kilobytes, does the documentation mean 1000 bytes or 1024 bytes?
Hi
I would like to have a project using 52840 witth softdevice 17, and I need to use internal flash to make a USB mass storage device
I reference to ....\examples...
Hi,
I need to create partition of size 4kb but using psa_ps_set() I could not able create partition of size more than 1Kb, If I try to create 4 kb Partition it's throwing...
Hello,
Creating a simple project in nrf connect 2.6.1 I start with looking at power consumption.
I need upgrade over USB, so I have added this to .prj:
In the...
software: ncs 2.5.0, zephyr\samples\drivers\counter\alarm
hardware: nRF52840dk
Step1: main.c is not be r evised!!!
Step2: prj.conf like this:
Step3: overlay file...
Hi Nordic Team,
I am currently working on a project that involves two devices, both using the nRF52840 microcontroller.
Current Setup:
Device A : I have successfully...
hello Nordic
we are working with ncs v2.5.0 trying to migrate to 2.7.0
1. so that there is several rcs, should i take v2.7.0-rc3 or v2.7.0 ?
2. while choosing v2.7.0...
