Does the s110 stack allow retrying pairing procedure?
It looks like the stack (peripheral) always ends with disconnect upon invalid passkey.
We would like to explore the...
Hi Guys,
since yesterday i am trying to get the DFU with Softdevice S110 (BLE) v7-alpha3 working but haven't succeeded yet. My process is the following:
s110_nrf51822_7...
Hi All,
i would like to know about
1) what is channel in nrf51288?
2) is there any mathematical relationship between channel no and pin no as in ble_app_hrs
example channel...
Hi,
I use UART bootloader SDK example(dfu_dual_bank_hci) to do update firmware on EK PCA10001 board,it can work ok.But i changed the HCI_SLIP_UART_RX_PIN_NUMBER and HCI_SLIP_UART_TX_PIN_NUMBER...
Hi. I have been trying get a notification through ANCS.
I have created an app which is made by modifying ble_app_ancs sample.
It works basically but there is one problem...
Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
Hi!
I’m developing an application using nRF SDK 2.9.0 with the Xiao BLE Sense . I created a new project based on Zephyr’s UART peripheral example.
The application runs...
I’m trying to implement DFU upgrade of NRF5340, I can send the image (./build_5340_app/build/signed_by_mcuboot_and_b0_s1_image.bin) to the device when running and it seems...
According to the documentation, you should run azure_iot_hub_dps_reset() in order to force DPS registration again.
But if the device has previously been enrolled and a device...
1. What is the Bluetooth version in NCS 2.6.1?
2. How to get Bluetooth version from NCS? is there any variable? I cannot find it in the release note neither. https://docs...
Hello,
I am using nRF Connect SDK v2.9.0, and nRF54l15 board. I enabled the watchdog timer and used its driver in zephyr/drivers/watchdog.h
It seems to work fine. The...
I have checked the PWM library in the nRF Connect SDK, and it seems that the library does not support init and deinit functions. The function pwm_set_pulse_dt(&pwm_led, 0...
Hello,
I’m currently working with a custom board based on the nRF9160 SiP, and I would like to measure the LTE-M TX power after the antenna impedance matching circuit. Ideally...
I am using the nrf52840 chip on a custom made PCB that is powered by a USB-C which provides it with 5V.This 5V is then converted to 12V using CH224K which then is wired to...
Hi,
we have ESB PTX and PRX couple from nRF54H20 nRF54H20DK (rev. 0.9.1), SDK: v2.9.0-nRF54H20-rc2 and the same Toolchain, IDE: VSCode + nRF Connect plugin build for CPURAD...
Using wireless sensors with nRF54L15, the sensors do not need to be connected, only broadcast a small amount of information. There will be 50-60 thousand nodes, and they are...
Hi, I'm trying to setup serial recovery in my project, in order to update firmware via USB cdc-acm.
I'm following this exercise from the academy which seems what I need...
Hi. I can't build the hello_dect example using cmake, the build process is failed with the following error: In file included from /home/cybermag/ncs/nrf/modules/trusted-firmware...
Hello!
I am interested in the Non-IP Data Delivery support in the nRF9160 module. In the description of AT commands, I did not see an opportunity to set PDP-type="Non-IP...
We use a module like EC2832AA1. I checked that nRF52832-QFAA-R is used for this module. This module has ap-protect enabled. So I added the command "nrfjprog --recover" to...
