Does the s110 stack allow retrying pairing procedure?
It looks like the stack (peripheral) always ends with disconnect upon invalid passkey.
We would like to explore the...
Hi Guys,
since yesterday i am trying to get the DFU with Softdevice S110 (BLE) v7-alpha3 working but haven't succeeded yet. My process is the following:
s110_nrf51822_7...
Hi All,
i would like to know about
1) what is channel in nrf51288?
2) is there any mathematical relationship between channel no and pin no as in ble_app_hrs
example channel...
Hi,
I use UART bootloader SDK example(dfu_dual_bank_hci) to do update firmware on EK PCA10001 board,it can work ok.But i changed the HCI_SLIP_UART_RX_PIN_NUMBER and HCI_SLIP_UART_TX_PIN_NUMBER...
Hi. I have been trying get a notification through ANCS.
I have created an app which is made by modifying ble_app_ancs sample.
It works basically but there is one problem...
Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
Hi,Team,
I am developing Pawr using nrf54l15-dk.
For the Pawr example I refer to E:\NCS\v2.8.0\zephyr\samples\bluetooth\periodic_adv_rsp and periodic_sync_rsp.
Regarding...
Hi everyone,
I'm new to Nordic development and currently working with a custom board based on the BC40C module (using an nRF5340). I’m facing an issue with the Bluetooth...
I’m working with nRF9151 + Toolchain 2.9.0 and wanted to share my experience & issue while sending ~7kB data over UART. I’ve tried both DMA & FIFO-based approaches — here...
I am designing a wireless sensor pcb with the nRF52840. I am essentially following the Circuit configuration no. 4 schematic for QIAA aQFN73 from the datasheet to a tee (schematic...
Hello,
I have bought a couple of Nordic NRF54L15 DKs, and it seems that the distance measurement toolbox that was compatible with the NRF52 series is not supported in...
We have nRF54H20DK (rev. 0.9.1), SDK: v2.9.0-nRF54H20-1 and the same Toolchain, IDE: VSCode + nRF Connect plugin
We need to control the GPIO LEDs from two cores ( P9.00...
Hello, as the 32.768khz PPM of our product is out of the range, so i need to fine tune the C1/C2, now C1 and C2 are 22pF, is it in range? what is the range for C1 and C2,...
So i am currently referring this ticket and from that I get to know that when when setting parameters for create config (HCI_LE_CS_Create_Config) command for channel sounding...
Hi,
I’m currently working with the nRF52840 DK configured as a BLE Central device. The peripheral device is a Flutter-based mobile application acting as a BLE Peripheral...
I'm having trouble porting my project from the older SDK (2.6.0) to the new SDK.
I thought the most straightforward way to do that would be to start with a sample project...
I am developing a Bluetooth Low Energy (BLE) application based on Channel Sounding (CS) using the nRF Connect SDK v3.0.2 on ME54BS01 modules from Minew Semiconductor (powered...
Hello DevZone,
Our team has been working on a customized firmware solution that has been flashed onto the nRF52840 DK to meet specific requirements.
We’ve noted that the...
Hi everyone,
I wanted to share an update on the BLE issue I’m experiencing with the BC40C (nRF5340) module on my custom PCB. I initially described the problem in this ,...
