Hi,
I use UART bootloader SDK example(dfu_dual_bank_hci) to do update firmware on EK PCA10001 board,it can work ok.But i changed the HCI_SLIP_UART_RX_PIN_NUMBER and HCI_SLIP_UART_TX_PIN_NUMBER...
Hi. I have been trying get a notification through ANCS.
I have created an app which is made by modifying ble_app_ancs sample.
It works basically but there is one problem...
Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
To be able to upgrade FW through UART, a bootloader for nrf51822 is required in my project. I have tried out the example bootloader in SDK. But this example is using softdevice...
I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
Hello
I use sdk v17 and nRF52DK. I want to use mpu6050 sensor in the example of ble_app_uart. SDK provides a driver for mpu6050, but I am not good enough to use it.
https...
Hi, I'm a beginner with these Nordic DKs. I'm just trying to connect it to my computer and get familiar with the hardware and firmware. However, when I plug in the DK via...
i want to store and retrieve data in flash. i followed steps as in the sdk infocenter but i am not getting the interrupt after fs_store(). Actually return value of fs_store...
Hi,
In my current project based on SDK 15.3 and sd140, I am using nrf52840 in both peripheral and central devices. I need to be able to maintain 10 concurrent connections...
Hi i am using the nRF52dk and i am trying to control a bldc can anyone help me to guide in how i can generate a pwm to get a sin wave
best regards Nikolai
Currently I want to build the light_switch examples from the nrf5_SDK_for_Mesh_v4.2.0 on my nrf52840 dev board but this gives the following error "boards.h: No such file or...
Hi,
I am working on a project of throughput data from sensors to my central via nrf52805 through a notifying service (SDK16.0.0).
Symptom description
We have app from...
Hello,
I want to use I2C slave on nrf9160, but there is no I2C slave driver implementation.
So I read that instead of this, I can use nrfx twis drivers on nrf9160.
I...
What am I missing when
NRF_SPI_MNGR_DEF(my_spi_mgr, 2560, 0);
causes:
../../../../../../integration/nrfx/legacy/nrf_drv_spi.h:120:37: error: 'NRF_DRV_SPI_INSTANCE_0...
Hey all! I have been using your amazing app timer for a while now but I was wondering if there was a better way to create a low power delay than my current design which goes...
Hello,
My application is the ble_app_uart example of SDK 15.3 extended, and using S112. I'd like to use constant latency mode. Given the app uses S112 for BLE, should I...
Hello,
In demo code of Central_Uart code in nRF Connect SDK, when the scanning is started the scan address (MAC) keeps on changing everytime the code is run. (The central...
Hi, We have a product with nrf24L01p Gazell (LastChangedRevision: 133) that acts as a Host. At the moment I'm trying to pair with this host via a PCA10040 Devkit ( nRF52832...
