Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
To be able to upgrade FW through UART, a bootloader for nrf51822 is required in my project. I have tried out the example bootloader in SDK. But this example is using softdevice...
I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi Folks,
Can you please let me know if nRF52811 supports XIP (Execution in Place) feature where I can use SPI NOR Flash to the SoC and execute my code directly from Flash...
SDK 15.2
Mesh SDK 3.1.0
Base Example: Enocean_Switch
Im working on creating an LED dimming firmware that uses a long press on the Enocean remote to dim the LED. It works...
Hi there, I tested range on NRF52840 with Thread SDK, so I have got small enough range. The test has been performed indoor, power transmission 0dBm, the range result is 10m...
Hi. In our application we are reading the voltage on 3 Analog input pins via saadc. System is also a BLE central and UBD CDC device so lots going on.
Quite often the 3 analog...
We have a requirement for the ble-peripheral device that we are designing to be able to be "registered" to a user through their iphone. If that user has multiple iOS devices...
I would like to insert some asserts in my code to ensure that code is not running inside a interrupt handler, because this can cause hard to debug issues.
How can I check...
Hi,
I tried to program the Thingy52 with the node and bridge to set a Mesh and I got the message in red you can see at the attached.
Please advise.
Thanks
Hi,
After reading the nRF24L01 documentation, I have some questions regarding page 66 of the documentation ( https://infocenter.nordicsemi.com/pdf/nRF24L01P_PS_v1.0.pdf...
Hello,
Has anybody achieved to perform Mesh DFU over serial on a Raspberry Pi using nrfutil?
I can successfully perform it on Windows 7/10 (intel) so far with no problems...
Hi All,
I am running a modified example of the 'ble_app_multilink_central_pca10056_s140' project.... I am running this on a PCA10059 dongle. The project connects fine to...
I am getting following error while building the project.
undefined reference to `nrf_drv_timer_pause'
undefined reference to `nrf_drv_timer_clear'
I believe these...
I have uploaded the AT CLIENT firmware and I have connected my nRF9160 dk to my apn, but I don't find any type of AT commend to set a socket and open a port to send and receive...
Hi,
If fires multiple generic_onoff_client set LED = True command from PyACI libraries with Ack = True to multiple nodes, the generic_onoff_client will provide a "generic_on_off_status_handler...
Hi sir,
I want to know if nRF9160 is programmable or not, like other wireless microcontrollers i.e nRF51/52 and ESP32 etc.
If it is programmable, where can we find the...
