We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
Good day. I'm working on a custom board that uses nRF5340 as the main MCU with a WIFI module, nRF7002. The nRF5340 and nRF7002 are wired based on the nRF7002DK. When I uploaded...
My project as above.
I'm developing my code in nrf52832,with nrf SDK v17.0.0.
I try to add some customized params by FDS so that I can get them after the next run.
The...
Hello,
I am having trouble reading an interrupt on an nRF5340. This is on a custom board using the ISP2053 SIP.
We are using the high speed SPI interface on pins P0.08...
I'm unsure if this is the correct place to post since this is not a Nordic-specific issue.
I am using the P100 which is a nrf52840 connected to an HL7800 through a UART...
hi all
i want to use a chip antenna for nrf52840
but un data sheet there is not any sample layout or component details
for example i want to use this chip antenna
...
Subject: Query: Interfacing OLED SSD1306 with nRF52832 on Zephyr
Dear Zephyr Dev Zone Community,
I hope this message finds you well. I am currently working on a project...
Hello! The S140 7.3.0 SoftDevice docs say it requires 0x27000 of flash, but the SoftDevice hex only occupies 0x26634 bytes. This leaves 2508 bytes of hopefully unused flash...
Hello, I'm trying to confirm whether the front-end module (FEM) is actually active in my application. Here is a summary of what I have done so far:
Updated prj.conf...
I followed the example described in https://developer.nordicsemi.com/nRF_Connect_SDK/doc/2.2.0/nrf/ug_nrf52_developing.html#fota-updates
and the loaded the SMP Server example...
Hallo,
currently I test several options in regarding the use of advertising. I have a few nRF52840-DK and use Zephyr 2.7-99 and ncs. I have a question regarding combined...
We are using SDK v2.6.1 for our application, along with the Fanstel module WT02C40C.
In our application, we provide internet connectivity to the WT02C40C module via a mobile...
Hi,
I have a makefile generating an elf and then a hex and bin file for a nrf52 project. Now I builded up a zip file for bootloading. Which works as well.
Now in our CI...
