Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Hi all!
My question is:
My own application is built based on the example "ble_app_template", and according to the nrf51 SDK - Examples - BLE Peripheral, this example...
Hi All,
Hopefully this is just a quick question... but I was wondering, if I set a breakpoint in my program while I am using the app_scheduler and app_timer2, should this...
Hey,
I noticed that in the SDK v1.6.0 a Kconfig option CONFIG_LOG_BACKEND_FS was added. However, I cannot find any information on how to use it.
I would like to be able...
I have included PWM library in BLE uart example to control the servo motor. I am able to import the library successfully and able to control the servo. Below is my init_pwm...
Hi,
I would like to know which soft device version is used in my nrf52840 board.
I know it's S140, but I understand that there are different versions for that.
Thanks...
Hi,
I am developing an application based on the aws_iot sample which all works fine.
The application captures data from a sensor and publishes it to AWS.
However, during...
Hello NRF ,
We have been using NRF9160 DK GEN-1 board for NB-IOT and GNSS tracking and able to configure network SIM as well as the NRF cloud .
We have used SDK 1.4.2...
Hello Nordic,
I had to reload a new nrfcloud certificate to my nrf9160DK. An active iBasis SIM card is attached to my nrfcloud account.
I followed these instructions:...
Hi everyone,
I have 1 board normal node(client+server) and 1 board LPN(client+server). I can send message from client of LPN to server of normal node, but i can't send message...
Hello,
I have a design where I am using an nRF52840 along with a SKY66112-11 and am using Zephyr/MPSL for both BLE and Thread. Some questions:
1) The .dts node has pa_gain_db...
Hi,
I was testing the GPS performance of the the thingie91. The default application (asset_tracker) works perfectly, but uses AGPS from the nordic cloud.
The asset_tracker_v2...
Hi all,
We run into a problem where our central product (a remote control) connects to the wrong device. We are using SDK v14.2.0 and softdevice S132 version 5.1.0. At...
Hallo,
I'm using a 52840dongle.
Uart ( PC-Terminal Debugging)
Radio ( reading 51822)
I2C Display
is working well
No i need to write and read data to/from a spi...
I have a serial OLED LCD on my SPI bus on my nrf52840 I want to do periodic LCD refresh by sending it's frame buffer without involving CPU.
I already know how to do SPI...
Hello!
I flashed the light_bulb example(NRF5 SDK v.4.2.0) hex to an nRF52840 Dongle using nRF Connect.
After reset, LED2 lights blue.
I do have an existing Zigbee network...
