Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Hi all!
My question is:
My own application is built based on the example "ble_app_template", and according to the nrf51 SDK - Examples - BLE Peripheral, this example...
Hi,
I am using ancs service to get some information of my iphone.
I use nRF51822 microcontroller and Nordic suggests to use the new SDK (5.2) for new microcontroller...
Hello.
I am trying the SEGGER Embedded studio's open nRF connect SDK project, but it fails with an error like the one in the image. How can I make it succeed?
SEGGER...
I am doing something really really crazy, that's writing some application on PC using opcode serial port for configuration a light switch server (maybe light switch client...
Hey all,
I've been using the SDK for Thread for quite a while and got all the basic stuff up and running with Thread and the nRF52840DK, RPi Border Router, etc.
For example...
Hello, I'm working with nRF5340 DK with Zigbee communication. I'm getting RSSI values between 0-255, but I'm more interested in the value in dBm, so I would like to convert...
Hello,
I developed the code on nRF52-DK with Segger.And also I want to program this code to MDBT42Q chip with nRF52-DK.
What are the circuits and software programs where...
Hello, I' trying to use the Serial LTE Modem application on an Actinius Icarus board. I configured the nRF project for the correct target, enabled COAP support, set Nb-IoT...
After upgrading the nRF-Command-Line-Tools from 9.8.1 to 10.12.1 the RTT output of JLinkRTTClient stopped working when doing a nrfjprog --reset. Interestingly it still works...
Hello, i've tested dfu process from secure_bootloader with different app examples with success (ble_app_blinky, ble_app_uart, even a custom application) but, when I try the...
Hi, I want to use normal GPS data (not AGPS) to send to my MQTT server.
I work well with MQTT_Simple to send sensor data to my server.
I see a GPS example in /nrf/samples...
Hello,
I have application that is sending data over BLE every 5 minutes.
I want to implement DFU using BLE. I don't have any single button on my device.
What should...
In the software NRf Connect Desktop.
The packet length (bytes) variable. What part of the Bluetooth packet does this change.
How does one calculate the number of transmitted...
Hi,
I have created my BLE peripheral application with custom services. Now i want to add DFU feature to it.
I have independently checked DFU test images given in nRF5...
Hi,
I've developed a PJT that works properly on nrf52832. Now I'm trying to migrate it to PCA10056 for USB developement.
Several attempts have been made but problem...
Isn't there an easier way to use the SDK? For example, to use pwm, you need to change nrf_pwm_enable to 1 and nrfx_pwm_enable, nrfx_pwm0_enable, load_mode, step_mode, base_clock...
