Does the s110 stack allow retrying pairing procedure?
It looks like the stack (peripheral) always ends with disconnect upon invalid passkey.
We would like to explore the...
Hi Guys,
since yesterday i am trying to get the DFU with Softdevice S110 (BLE) v7-alpha3 working but haven't succeeded yet. My process is the following:
s110_nrf51822_7...
Hi All,
i would like to know about
1) what is channel in nrf51288?
2) is there any mathematical relationship between channel no and pin no as in ble_app_hrs
example channel...
Hi,
I use UART bootloader SDK example(dfu_dual_bank_hci) to do update firmware on EK PCA10001 board,it can work ok.But i changed the HCI_SLIP_UART_RX_PIN_NUMBER and HCI_SLIP_UART_TX_PIN_NUMBER...
Hi. I have been trying get a notification through ANCS.
I have created an app which is made by modifying ble_app_ancs sample.
It works basically but there is one problem...
Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
Hello,
Hardware: NRF52840, Development Software: any
I am hoping to generate 3, or ideally 4 separate (independent duty cycles) PWM signals at a frequency of at least...
I use sdk13.0,s332,when my system working,it will auto reset about 129 seconds per time,I make a breakpoint,find it caused by "softdevice_fault_handler",when it reset,the...
Hello,
I am starting development on what should be a straightforward application using the nRF52832. It is actually this BLE module , which contains the nRF52832. However...
I am wondering if I could have access to a mechanical drawing or 3D model of the N RF52840-DK . Does anyone know where I could find either of these?
Thanks,
Julia
I am trying to understand why my program is returning this error (NRF_ERROR_RESOURCES). I read through a lot of other posts in the devzone and tried replicating them, but...
My board is nRF52840 + S140 + nRF5_SDK_15.2.0_9412b96, my configue as below picture and file "ywk_bsp_ble.c" .
When nRF Connect APP connect my device, it alway be disconnected...
Hello,
I am using nRF52832 (BT832 module designed by fanstel) based module for my application. we have developed customized PCB using the module. while evaluating the...
What chip supports Open Thread? SDK and softdevice versions supported?
We are in evaluation phase looking for potential radio manufacturers for an upcoming project.
Any...
I see similar posts, but no answer of this problem. I have similar code that work on my FW, but when I port it to my BSL, advertising is not working and when I look at return...
I am migrating from SDK11? to SDK15.3 and noticed nrf_drv_common.c is no longer available and has no replacement although nrfx_common seems to have replaced nrf_drv_common...
Hi, what are the (security) implications of running bootloader with #define NRF_BL_APP_CRC_CHECK_SKIPPED_ON_GPREGRET2 1 in production code? We use sdk15.0.0 with secure dfu...
Hi everyone,
I have an issue with power consuption. I work with the SDK15.2.0 and the SoftDevice S140 on a custom board.
I launch the ble_app_pwr_profiling example on...
I wasn't receiving any log messages while debugging the ble_app_uart_c example using SES so I enabled appropriate logging functions and set them to level 4 in config.h. Still...
We are using NRF_SDH_DISPATCH_MODEL_APPSH, and are generally very happy with it (especially for BLE events). However, I'm trying to retrofit error handling around complex...
