Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Hi,
I’m working on loading batch data from a BLE server using SDK version 2.8.0 with the nRF9161-DK hardware, and I’ve encountered a couple of issues.
Different Results...
Hello,
the mass production firmware of our product was generated on NCS 2.2.0 (MATTER 1.1). Now, we are attempting to OTA upgrade our product to the firmware based on NCS...
When dealing with low power access via NTN (via Skylo), is there any limitation about any particular use of SW?
Like, is Zephyr or other RTOS combinable with the Skylo certified...
I'm trying to flash a XIAO nrf52840 following the instructions for flashing with UF2 but it won't seem to work. After I drag and drop the zephyr.uf2 file in the mounted drive...
Hello. I am trying to implement stable connection between my nordic nrf5340 and Samsung Galaxy Buds3 earbuds. I did it based on ble audio example with two connections (one...
I have a 7002dk dev kit. Currently for evaluating the nrf5340, which will be used in my product. Currently i am trying to evaluate if it is possible to use the nRF5340 USB...
Hi,
I am using two nRF52833 DK and both are connected with nRF21540.I notice that when I have a very high throughput, never stop sending 244 bytes, I will notice that average...
Hi,
I would like to ask about the future plans for Zigbee development, as the current situation is a bit confusing.
From what I’ve observed, Zigbee R22 has been deprecated...
My team recently acquired two NRF24 transceivers to use on our drone project. Personally I've used NRF24 modules before and have successfully paired them with Arduino and...
Hi all,
i just received 2 nRF54L15-DK boards. Both I am not able do program - I tried:
1. nRF Connect for Desktop
* I did not make any change on the board afre unpacking...
I want to use the boards NRF-5340DK or NRF-52840 with the external host for the channel sounding feature. Can we use the feature on the mentioned board? If so, can you please...
I'm trying to send and receive an extended advertisement packet with about 100bytes of payload.
I started with the sample extended_adv example.
I 1st validated that using...
Hello. We are updating firmware to use nrf sdk 2.9.1 (from 2.5.2). Below is my proj.conf, should I expect any breaking changes?
############################
# Stacks...
Hi,
I want to configure the nRF9160's internal flash storage_partition, it has 32KB currently, I want to change it to 100KB. How to do that? Using nrf9160dk_nrf9160_ns.overlay...
Toolchain v2.70, SDK v2.6.1, VS Code, Windows
Code derived from UDP sample works on DK board but fails on custom device.
Device is using DK board configuration, but no...
