Hi,
I use UART bootloader SDK example(dfu_dual_bank_hci) to do update firmware on EK PCA10001 board,it can work ok.But i changed the HCI_SLIP_UART_RX_PIN_NUMBER and HCI_SLIP_UART_TX_PIN_NUMBER...
Hi. I have been trying get a notification through ANCS.
I have created an app which is made by modifying ble_app_ancs sample.
It works basically but there is one problem...
Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
To be able to upgrade FW through UART, a bootloader for nrf51822 is required in my project. I have tried out the example bootloader in SDK. But this example is using softdevice...
I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
Above image is our design for nRF51822. Design also contains Accelerometer and WiFi (ESP8266).
My problem is, I am not able to see nRF BLE advertisement while scanning...
Hi!
Can someone please help me debug this example. It used to work, then I changed number of peripheral links to 1 (to see what RAM suggestion would be), then returned it...
Hi!
I try to flash nrf52 from keil and message appear:
The firmware of the connected J-link (S/N: xxxxxxxx) does not support the following memory access: Read @ 0x02000004...
Hello,
I want to enable UART only when data transfer is necessary.
I am using nrf 52832 and sdk 14.0.0.
I am using "ble_app_uart".
I could not find the answer I...
Hello everyone.
I have a question about sleep_mode_enter() behavior.
I'm using nRF5_SDK_12.3.0 and nRF51822 for my project.
I put a lot of printf statements in the example...
Hello All,
I am working two BLE chipset , one is nordic and another one different make (TI) so is it possible to communicate between two different make BLEs using our nordic...
In NRF 51822 custom board I uploaded ble_app_uart code. Program uploaded successfully. But not able to discover from Phone and Tablet, where in another board it works properly...
hello,everyone.we want to use pin3 and pin4 as txd and rxd,but there has error.could you give us some help?
void debug_uart_init(void)
{
uint32_t err_code;
const app_uart_comm_params_t...
hi,
i made my nrf 52840 dk advertise unlimitedly using ble_app_uart example. connected and disconnected several times using nrfconnect app. it really works fine. with this...
Hi,
I'm using nRF52832 and LDETECT mode for GPIOTE PORT event to detect multiple interruption.
Even though LDETECT mode is described in the product sheet page 112 and...
Dear friends, my current measuing instrument is Power Profiler Kit. I have some troubles when i use it. e.g. 1) how to completely stop an updating plot that a PPK draws? even...
Dear friends, 1) As shown in the pic below, there are some values "max:13.70, min:3.33, rms:3.45..." at the bottom of the pic. which area is these values calculated from?...
I'm finding fairly large lags with the RTC2 I'm using. I use an app_timer to sample the current RTC count value as a timestamp (MM:SS:Hundredth-of-a-second) and send it out...
Hi all,
I have a question to complete the tutorial 'Setting up device firmware update(DFU) on the nRF5 DK'. this
I have tried to set up my nRF51 Development Kit.
Everything...
I am facing wierd behavior after migrating to sdk 10 serialization code i.e ble_connectivity example program. Unable to scan peripheral devices, some times unable to connect...
