We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
Hi,
We are using sdk12.3.0 sd130 v2 on nRF51822(32KRAM version). We want one central to connect to at least 3 peripherals. We are starting with ble_app_hrs example at the...
Configuration:
nRF5_SDK_13.0.0_04a0bfd
PCA10040
ARMGCC
Background:
I have created custom service based on ble_nus service. I have created 4 characteristics with notify...
I'm concerned about users writing too much or invalid NDEF data to the NFC function.
This could result in parse errors or buffer overflows leading to system crashes/malfunction...
Good Morning,
I need help for integrating a wifi card of this type or another that may suggest. With explanation of connection in the pinp Gpio of the thingy52 board, what...
Hello everyone,
I am looking to start developing something using nfc but I am unable to do so.
I am using SDK v12 and it has nfc examples as well like "record_url" or "adafruit...
Hi,
How to integrate both over-the-air and uart bootloader application for an device? We have a custom board with nrf51822 chipset, and we need to implement the firmware...
Hello,
I'm currently experimenting with the dual-bank bootloader in SDK 13.1. According to the documentation, if the new application can be activated, it is copied from...
Hello everyone,
I'm developing a new device using the nRF52832 but I have 2 questions before I send my PCB to manufacture, I hope you can help me out:
Is there any...
Hi,
Congratulations on releasing nRF Connect v2.0!
Unfortunately, I'm having trouble with adding apps behind corporate SSL proxy. Is there a workaround for this?
Please...
Hi,
I am trying to change the uart example using NRF 52 with SDK 12.3, so that I would hold a button pressed and it would send the time of button being pressed after release...
Hello!
I am putting (with a wave generator) a square wave on pin 17 of the microcontroller, and I want that same wave to come out on pin 18. How do I do that? Do you have...
Hello,
I need to transfer a lot of data over USB. I configured the USB as a USB_CDC_ACM on the nrf52840.
Everything works but the problem that i'm running into is that...
Hi there,
I'm currently using micro-ecc on an nRF52 compiled using Nordic's makefiles and implementing the secp256r1 curve. I'm mirroring this in Node.js using the Crypto...
Hey,
Can the nRF52 support 'Thread' / '6LoWPAN' protocols in the future?
Can the component support it (PHY wise etc) with the right 'softDevice' stack drivers?
Thanks...
