I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Our IoT device is connecting to 2 different cell towers on the same carrier. Cell tower 'A' has signal of -90dBm, tower 'B' has signal of -105dBm.
The device is mainly attempting...
Hi,
I am using nRF54L15 with SDK v3.0.2 . I am facing an issue while initializing the LSM6DS3 sensor on a custom PCB.
Device Initialization Code:
#define...
I am developing a modbus server application for nrf54L15 in nrf sdk v3.2.3. But I ran into an issue where using MODBUS_MODE_ASCII requires UART_CFG_DATA_BITS_7. The modbus...
Dear Nordic,
The west build system is not acceptable for firmware development.
Firmware != Software. When we create firmware for a product, it must last for years. We...
Hi,
I've reliably implemented a Software Serial library on the nRF52832 using GPIOTE and nrf_delay_us to sample the 8 bits. I tried making this work more efficiently using...
Hi
Is it possible to use the 54dk for programming of our new board with the nRF54L15 running on 1.8V?
Is the voltage configurable on the 54 dk?
Best regards
Peer
I am using nRF Connect SDK (NCS) v2.9.0 for a Matter project.
Currently, the Manual Pairing Code generated is 21 digits long. I need to change this output to be 11 digits...
We follow the youtube video: www.youtube.com/watch
to add battery charging and fuel gauging to our nRF52832 Series project.
It works, but after we enable
CONFIG_PM_DEVICE...
Hi nordic team
I am working with the Nordic nRF5340 SoC using Zephyr RTOS .
Hardware
External QSPI flash:
MX25R6435F
QSPI configuration (DeviceTree):
...
Hardware: nRF9151 DK Modem firmware: mfw_nrf91x1_2.0.4 Carrier: Verizon (PLMN 311480), Band 13 Antenna: External Problem The modem continuously reselects between two cells...
Hi Nordic team,
In the context of adapting the software for our custom PCB I need to make some changes in some devicetree nodes for the net core. Therefore I wanted to add...
I designed a circuit using the NRF54 to connect via Bluetooth and control several peripherals. I program the chip using the Debug Out of the NRF54L15 DK . The code can be...
Just bringing this to your attention. This has been an issue since at least 2.6.1, and appears to still be a problem in main.
static void connected(struct bt_conn...
