Does the s110 stack allow retrying pairing procedure?
It looks like the stack (peripheral) always ends with disconnect upon invalid passkey.
We would like to explore the...
Hi Guys,
since yesterday i am trying to get the DFU with Softdevice S110 (BLE) v7-alpha3 working but haven't succeeded yet. My process is the following:
s110_nrf51822_7...
Hi All,
i would like to know about
1) what is channel in nrf51288?
2) is there any mathematical relationship between channel no and pin no as in ble_app_hrs
example channel...
Hi,
I use UART bootloader SDK example(dfu_dual_bank_hci) to do update firmware on EK PCA10001 board,it can work ok.But i changed the HCI_SLIP_UART_RX_PIN_NUMBER and HCI_SLIP_UART_TX_PIN_NUMBER...
Hi. I have been trying get a notification through ANCS.
I have created an app which is made by modifying ble_app_ancs sample.
It works basically but there is one problem...
Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
Hello,
Some questions regarding the linker script for the 8.1 SDK for SD110.
I was able to get an environment set up with ARM GCC, Make, etc. and compiled my program...
I have a program running with SD 7.2 and SPI on my nrF51822 talking to a SPI slave device. I use GPIOTE triggered on an edge to set a chip select line and read bytes from...
I have a LED dimming project that uses nRF51822 and nrf_pwm_noglitch. If I turn to 100% duty cycle, then it will be stuck at 100% unless I turn it to 0%.
So in other words...
The board is simply an nrf51822 with a crystal and required caps and resistors, without any LEDs. When I try to flash any firmware, I get an OK that the firmware has been...
Hello guys,
I am working on the project where I am making a network4 nrf24l01 transceivers, such that one can broadcast the text message from one transceiver at the base...
Hi, I'm trying to write a long byte array with the nrf master control panel on android. I'm unsure if the app is able to, but in any case I'm not getting the event: BLE_EVT_USER_MEM_REQUEST...
Hi,
I have my custom nRF51822 board, and i used to flash the firmware through nRF51 DK kit.
As there are two ports through which we can load external boards i was using...
Hi,
I'm trying to build a prototype using the Adafruit nRF8001 Breakout and an mbed ARM CPU.
After Reset, I get a Device Started Event, telling me the chip is in Setup...
Hi,
In SD100v8, there is capability of checking the application version, to make sure no downgrade (or any other criteria required). The reference is in Link to SDK
...
There is a blog post for advertising but none for connection interval.
I am wondering how big is the difference for this example:
Measurement on peripheral every 4 seconds...
Hi...
Can anybody help me to run ble_peripheral example (ble_app_hrs for S130). I have build and load the code successfully but cant see the advertisement. But while debugging...
Hi,
Got stuck on an issue that has come and gone and then working fine, and are now back again.
I use a nrf51 module with the led-button-service example (sdk 5.2). It...
So, we are pretty far along in development (I have inherited the project) with an nrf51822, SDK 4.4.2 and SoftDevice "6.0.0-alpha". We are nearing release, and I was told...
I have set the POFCON to enable the power failure comparator and set the voltage level to2.5 volts. How do I know when the battery voltage is below the 2.5 volt level? How...
