Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
The chip I 'm using is the nRF52840, the sdk and toolchain versions are both 2.5.0, my code is here :
When I call spim3 peripheral with nrfx library, I add
CONFIG_NRFX_SPIM3...
Hello, hope to find you well. I'm a beginner involved in a project that's migrating from the old SDK to NRF Connect (VSCode). The project uses nrf_crypto.h and nrf_crypto_rng...
We recently purchased the module 453-00052R from Digi-Key and have successfully implemented it into our project. The design is complete, and we are now attempting to flash...
Hi,
I am trying Asset Tracker V2 application in my custom board and rechecking results with DK to ensure no hardware reasons are there. Using SIM supplied with DK and...
Hi Support Team
Our project need 8mA charge current, how to configure charge current of nPM1300 to 8mA？ Or could you provides us other nPM chip or solution that can meet...
Hi all,
I have a custom board running on nrf9161. I need to flash the custom board with the NRF9160-DK. But I am running into some issues. the development is at early stages...
Hi,
I'm trying to add a manufacturing specific attribute to the On/Off cluster.
To do this I have so far created a custom attribute list with ZB_ZCL_DECLARE_ON_OFF_ATTRIB_LIST_CUSTOM...
Hi NordicTeam
i am working with the Mesh Dimming server example out of the SDK MESH 5.0.0.
While investigation the Packet loss in my prevous ticket i was wondering if...
Hi,
Working with the NRF5340-nrf7002 and the W25Q16RV flash memory in our project.
Initially, I configured an 8MB( W25Q64RV) external flash without issues and tested...
I've been testing the FMDN locator tag sample application with a nRF52840 devkit and I would very much like to get an answer to the following questions:
1. Is it possible...
Hi, I'm having an issue with the bt_mesh_resume() function in my project based on Zephyr and Bluetooth Mesh. My code is trying to cycle the Mesh network on and off to save...
Greetings
I have been going through the BLE fundamentals course, and I am currently on Lesson 4 exercise 1, which entails creating custom services. I have went through the...
I am working with nRF Connect SDK 2.6.1 on a Central and a Peripheral and I am running the BAP similar to the nRF Audio Example. I am using out of band pairing over UART for...
Hi,
I am working on application code for the nrf9160. Current NCS version is 1.5.1, although I do not think my ancient NCS version is relevant to this issue.
I have removed...
I can't find any documentation on how you are supposed to define partitions in NCS 2.7 when using MCUboot. Previously Partition Manager was responsible for this and was overriding...
