Hi Nordic Team,
The atomic fifo implementation is based on armv7-M, right now I want to port it into cortex-A processor, I made some changes to get it compiled without...
Hi,
Kit:nrf5340
Can you please tell me if there is any example in nrf connect SDK v1.5.0 related to data transfer concepts.
Is ble controller will be enabled during...
I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
Hello,
I am facing an issue with SPI when the SoftDevice S132 is enabled and i cannot figure out what the problem is.
The following test works perfectly when SoftDevice...
Hello
I'm trying to use the example code for ble_app_uart and it doesn't seem to work. I copied the folder for pca10028 and changed processor from nrf51422 to nrf51802 everywhere...
I am using four ADC inputs to the 9160.
I am driving each input from an op amp buffer as in the attached schematic.
ADC channels 0, 2, and 3 work as expected. As for channel...
I am trying to move our existing code based on the recommended NCS SDK. I was able to get MCU boot and SMP working, however, the update is extremely slow. I now seem to be...
I have developed a project using 9160. When I start up with the client board, the log will show that at command execution error occurs when I start up. Why is this? I admit...
Hello nRF community,
I am currently testing some Memfault application that comes with the nRF SDK v1.7.0. I have a custom board designed around the nRF9160 and have been...
Hey,
I'm developing and upgrading a BT mesh to Zephyr 2.7.99 and the base functions work, but my Node keep crashing and I don't know from where. It gives the following...
First off, I see a new changed requirement for making Public tickets:
To raise a public support ticket you need to provide your location in profile. profile Please fill...
Hi Everyone,
I'm having problems getting GPIOTE_IRQHandler_v() to run.
"NRF_GPIOTE->INTENSET = 1" causes my Nano 33 BLE to crash if "(GPIOTE_CONFIG_POLARITY_LoToHi <<...
Hi!
I want to use the function strptime from time.h to convert a timestamp to unix time but get the error "implicit declaration of function 'strptime'; did you mean 'strftime...
Hi,
I am new to microwave board design, so I'd like a little advice please. I have attached photos of the 2.4ghz section of my board and would like to know if the component...
Hi,
I'm trying to integrate the secure_bootloader DFU code into the ble_app_uart_c example but am stuck on an error regarding not fitting in an 'UNPLACED_SECTIONS' region...
I'm trying to develop an Android app to get the BP, HRV, HR, SpO2, ECG, PPG, BPM, steps, activity, temperature, sleep quality from Spovan H02 fitness tracker ( www.spovan...
Hi, I am using Mesh v4.2.0 and nRF52840 light_lightness example but instead of button_event_handler, I am using GPIOTE to control the lights.
I want to toggle one LED with...
Hi
We are developing a system where 2 devices (NRF52840) advertise to each other (and eventually connect) in a highly reflective environment (the cargo hull of a ship)....
As mentioned here I installed the Intel versions:
VS Code 1.63.0
nRF-Command-Line-Tools 10.13.0
J-Link V7.58e
nRF Connect for VS Code
But flashing the sample...
