I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
Hello,
I am facing an issue with SPI when the SoftDevice S132 is enabled and i cannot figure out what the problem is.
The following test works perfectly when SoftDevice...
Hello!
So I can connect, disconnect and write to my applications characteristics via a PyQt5 GUI I threw together. On the python backend, I use Bleak to
search for devices...
Hi, I am developing using nrf52832 and st7735s.
Successfully displayed the lcd screen using the code in \examples\peripheral\gfx
However, when screen clear, text_8print...
Hi,
I am developing an embedded solution where I need to use a nrf52832 as bluetooth controller to detect advertisement packets from beacons. I flashed the zephyr hci_uart...
SDK version 1.7.1
I am working on a project involving a nRF9160 and the sample application nrf/samples/nrf9160/azire_iot_hub and working on reliability issues with disconnections...
Hell to all,
We are currently developing a device that are NRF52832 based on NRF SDK v16. It is in our plan to make use of the Wirepas stack too. At the beginning, it...
Hi
I have committed myself to building a central app that will be based on UART example replace an existing BLE soc that can no longer be found using the central.
My sensors...
hi
i am working on custom card in which nRF52832 is used.i am facing issue with advertising if i uncomment uart_init(); .it does not advertise if i uncomment uart_init(...
Hi,
I'm using S112 nRF52805 as the BLE Peripheral, and Mobile App as the BLE central.
So far, It's no problem to send data from peripheral to central. Could I send data...
Hello all,
I am workiong on nRF52833-DK evaluation board to implement our custom developement.
Using Generic OnOff light switch server and light application, I am transferring...
Hello,
I ran the throughput example ,but I found that setting the MTU size actually requires calling the bt_gatt_exchange_mtu function, which is different from sdk16.0 ...
Hi everyone!
I'm working at ble multilink throughput, and the basic info shows as follows.
chip: nRF52832(one central and eight peripherals)
sdk: nRF5 SDK v17.0.2
...
I am getting below error when editing dfu secure project as the baseline
/nrf_crypto_allocator.h: No such file or directory
the project is modified as below
<folder...
Hello everybody
With me is nrf52840_dongle that am using for wireless communication together with the protocol enhanced shockburst. To increase the signal range, am thinking...
Hello guys. Here with me I have both nRF9160-DK, hardware version 0.8.3 and Thingy:91 boards. I am on the nRF Connect SDK tag 1.2.0 and have nrf9160 SiP modem firmware updated...
Hello,
I have been searching in DevZone and looked at the nRF Connect SDK documentation but I am still confused about a thing: I have developed a BLE Mesh device and I managed...
Hi!
I'm using nrf5340dk development kit to program and debug my own custom nrf5340 board. Everything works and I can debug the code with SES but I can't see the RTT logging...
My application is a Central using SD140.
The connection to the peripheral is made successfully. What event will I get when the Central successfully writes to the connected...
