My goal is to control a RC toy drone (4-ch 2.4GHz) from a PC. I've seen some hacks (for example dzlsevilgeniuslair.blogspot.com.br/.../more-toy-quadcopter-hacking.html) using...
Hi Team,
Is it possible to implement the iOS application to track the iBeacon Component after closing the application(Background processing).
Please provide any example...
Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
Dear Sir.
I use these commands to connect the Modem ON and OFF.
I need to know if the result of the these commands the Modem communicates with the Cell tower ?
Please...
Hi,
I have nrf52833-DK. Where should I get started for DOA applications? I'm experienced with other nRF chips, but not for DF and RTL applications specifically.
Hello,
I try to debug a BLE connection with the nRF Sniffer. As a test, I used one nRF52 DK (PCA10040) as peripheral using nRF Connect and and Android phone as central device...
I'm using the HID keyboard as the base example. We're using prototype hardware so the connection gets dropped periodically due to ongoing hardware issues. But this has exposed...
Hi, nordic Engineer!
Merry Christmas！ I am using the DF to develop my project and considering simulation with the Bluetooth signal with antennas to build a customized antenna...
Hi,
I am trying to receive messages via Bluetooth mesh and forward them via UART (using UART async API) on the nrf9160DK. But when I try this, I get an assertion error from...
Hi,
I'm using SDK17.2 to develop nRF52810's application.
When APP_ERROR_CHECK or APP_ERROR_HANDLER have a fault which is caused by hardware or software, the system will...
Hi,
I want to trigger a wake up from System ON sleep (WFE) using the LDETECT signal on Zephyr.
I managed to wake up using Zephyr's gpio API but my understanding is that...
1. Nrf52840 acts as central and Nrf52832 acts as peripheral. when nrf52840 has connected with nrf52832, nrf52832 disconnected occasionally. Disconnect reason 0x0013. When...
Hi there!
I have recently managed to combine sht85 with light lightness server code. J-link is able to produce 2 values (Temperature and Humidity) whenever I key in the...
I has successfully built the following demos and run them on a nrf52840 dongle (board: nrf52840dongle_nrf52840) :
cdc-acm-console demo from Samples and Demos » Various...
Hello,
I'm struggling with DeviceTree support in Segger Embedded Studio and nRF5340. I want to use the I2C Modul.
So I defined in my (dts)overlay file
&i2c0 { status...
Hello,
I recently updated my nRF Connect to the latest version 3.9.3 and it also updated the programmer app to 2.1.0. After this update, the Programmer app does not detect...
Upload fail - Remote DFU invalid CRC error
i m facing this error while uploading firmware through DFU kindly any one help me to fix this issue using nRF 52810
Thanks
